3 Tighten the screws . 12 mm) (Accessory 4) in the holes shown on the diagram. Accessory4 Installation Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercially available) Firewall or metal support ¦ Installation Screw (M4X8) (commercially available) ¦ Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off. 1 Refer to the section (page 34) and then remove the hard rubber frame. 2 Drop open the faceplate by pressing the Release button. 4 Tighten the screws (o2 . 4 mm) (Accessory 5) in the holes shown on the diagram. 3 Tighten the screws . 12 mm) (Accessory 4) in the holes shown on the diagram. Accessory4 Accessory5 5 Tighten the screws (o2 . 6 mm) (Accessory 6) in the holes shown on the diagram. Accessory6 Never insert the screws in any other screw hole than the one specified. If you screw them in another hole, it will contact and may cause damage to the mechanical parts inside the unit. — 33 — Installation Installation ¦ Removing the 1 Engage the catch pins locks on the upper level. Upper the frame and pull Catch Lock Accessory2 Removal tool 2 When the upper level is removed, remove the lower two locations. ¦ Removing the 1 Refer to the section remove the hard rubber 2 Remove the screw (M4.8) on the back panel. 3 Insert the two removal tools deeply as shown. Screw (M4X8) (commercially available) Accessory2 Removal tool 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. The frame can be removed from the bottom side in the same manner. — 34 — 34— 34 — —— Troubleshooting Troubleshooting General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. ? There’s a source you can’t switch. . There’s no media inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't switch to each source. . The Disc changer isn’t connected. . Connect the Disc changer. If the Disc changer isn’t connected to it's input terminal, You can't switch to an external disc source. ? The memory is erased when the ignition is turned OFF. . The ignition and battery wire are incorrectly connected. . Connect the wire correctly, referring to the section on . ? There’s no loudness effect. . You’re using Non-fading preout. . Loudness has no effect in Non-fading preout. ? The Non-fading output can’t be turned ON or OFF. . The (page 27) is set is set on Rear preout. . Change it to Non-fading preout. ? The TEL mute function does not work. . The TEL mute wire is not connected properly. . Connect the wire correctly, referring to the section on . ? The TEL mute function turns ON even though the TEL mute wire is not connected. . The TEL mute wire is touching a metal part of the car. . Pull the TEL mute wire away from the metal part of the car. ? Even if Loudness for. . Tuner source is selected. . High-pitched tone isn't compensated source. ? No sound can be heard, or the . The fader or balance settings are . Center the fader and balance settings. . The input/output wires or wiring harness . Reconnect the input/output wires or the See the section on . . The values of Volume offset are low. . Turn up the Volume offset, referring to the section on
)
