Stimmen - 5, Durchschnittliche Bewertung: 3.4 ( )

Hersteller: Kenwood Dateigröße: 281.93 kb Dateiname: Unterrichtssprache:

When "OFF" is displayed, the standby mode is activated. The standby mode turns all functions off while leaving the power to the unit on. Use this mode when you want to have the display illuminated but don't want to listen to anything. NOTE The mode switches to the next mode from any mode which cannot be used. — 5— General English Volume Increasing Volume: Press the u button to turn up the volume. Decreasing Volume: Press the d button to turn down the volume. Attenuator This function allows you to turn down the Turning Attenuator On/Off: Press the ATT button to switch the attenuator on When the attenuator is on, the ATT indicator blinks. When the attenuator is off, the volume returns to the level. NOTE Turning the volume up, or turning it all the way down deactivates the attenuator function. Loudness This function amplifies low and high tones when the volume is turned down. The LOUD indicator lights up when the loudness function is on. Turning Loudness On/Off: Press the LOUD button for at least one second to switch the loudness on and off. 1 Press the AUD button control mode. 2 Selecting mode Press either the FM or AM Each time the button is pressed, change. Please refer to the following for modes. NOTE Source tone memory Each source ( tape, CD, FM, AM and disc memory in which to store the bass and treble tone settings. The settings made for a particular source are automatically whenever you use that source ( for mode uses the tone settings made for FM, AM for 3 Adjust each mode Press the 4/ . button. Please refer to the following for the adjusting values. 4 Press the AUD button to end the control mode. "BAS" : Adjust the bass level. Setting values: - 4 – + 4 "TRE" : Adjust the treble level. Setting values: - 4 – + 4 Audio Control Setting "BAL" : Adjust the balance level. Setting values: Left 15 – Right 15 Adjust various parameters of sound quality. — 6— "FAD" : Adjust the Setting values: Front – Rear 15 ec4/dB (Sound Coordinate) You can recall the best audio setting of the music. 1 Press the AUD button to enter the Sound 2 Press a preset button (#1-5). The preset settings of the bass and treble tones #1: Flat #2: Rock #3: Pops/Top 40 #4: Jazz #5: Easy 3 Press the AUD button to end the sound coordinate mode. NOTE Adjusting Time Adjust the time. 1 When the time is not displayed, display the time. 2 Press the CLK button for at least adjustment mode. The time display 3 • Adjusting the hours Press the FM button to advance the hours, button to make the hours go back. • Adjusting the minutes Press the . button to advance the minutes, or press the 4 button to make the minutes go back. 4 Press the CLK button to end the clock adjustment You can call the following settings with this function; bass center frequency, bass level, bass quality factor, bass extension, treble center frequency, and treble level setting. Clock display Turning clock display On/Off: Press the CLK button to switch the clock display on and off. The . indicator lights while the clock is displayed. — 7— General Tuner features English Theft Deterrent SRC The faceplate of the helping to deter theft. Projections Release button Grooves Removing the Faceplate: Press the release button. #1 ~ 6 AM The faceplate is unlocked, allowing you to detach AUTO / AME 4 . FM / CRSC AUD1 2 3 4 5 6 CLK ATT FFREW SRC PR OG PWR OFF AME ADJAUTO SCAN RDM REP TC/D.SCN M.RDMLOUD DISC CRSC HIGH POWER 40Wx40Wx 4 A.ADJ FM AM NOTE • The faceplate is a precision piece of equipment and can damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case while detached. • Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattaching the Faceplate: 1 Align the projections on the unit with the grooves on the faceplate. 2 Push the faceplate in until it clicks. The faceplate is locked in place, allowing you to use the unit. STEREO indicator Frequency Preset station number Band display indicator AUTO indicator — 8— Tuning You can choose between frequencies and manual 1 Press the SRC (source) button mode. "TUuE" is displayed when selected. 2 Press either the FM or AM button Each time you press the FM button, between FM1, FM2, and FM3 (which are preset stations) . Press the AM button to select the AM band. 3 Press the AUTO button to switch between auto and manual tuning. The AUTO indicator lights up only when auto seek tuning selected. 4 • Auto Seek Tuning Press the . button to seek higher frequencies. Press the 4 button to seek lower frequencies. • Manual Tuning Press the . button to increase the frequency by one step. Press the 4 button to decrease the frequency by one step. NOTE The STEREO indicator lights up when stereo broadcasts are being received. Station Preset Memory Store the frequency of a station. You can then recall that station with a single touch of a button. 1 Select the band/ station that you want to have stored. 2 Press t...

Herunterladen

Geben Sie zwei Ziffern: