Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Connect one end of the G9 cable to the audio source and the other end to the control unit. 2.Use the RCA cable to input analog stereo audio signals. D. CONNECTING POWER TO THE SYSTEM: Connect the subwoofer’s AC plug to the electrical wall outlet directly. ACCEPTABLE RANGE OF REMOTE CONTROLLER: Depending on the environment, satellite speakers(center,left,right,rear left, and rear right)can be placed on the wall. 1 2 CONTROL UNIT FUNCTIONS (FRONT PANEL): POWER: Use the button to operate power on / off 1& 5.1 CH INPUT LED INDICATOR: The LED indicates the system Is in 5.1-channel input mode. 2 or 3 INPUT LED INDICATOR: The LED indicates the system is in 2-channelinput mode. SURROUND LED INDICATOR: This LED will light up when in surround input mode . (This function does not operate upon 6CH input.) INPUT Aelect: Use the button to operate 1-3 INPUT MASTER VOL +: Press this key to increase master volume level MASTER VOL —: Press this key to decrease master volume level STANDBY LED INDICATOR: This LED indicates the system is in standby mode. When making functional adjustments the LED will flash. This LED will light up when the volume is adjusted to either maximum or minimum, indicating the volume level cannot be further increased or decreased. MUTE LED INDICATOR: This LED will flash when in mute mode. Q: Stereo Headphone Jack. REMOTE CONTROL FUNCTIONS: SPEAKERS CONTROL POWER: Press this key to operate standby on I off RESET: In the 6CH mode, press this key and the volume in each audio channel will return to its default value. In the 2CH mode, press this key and it will erase the SURROUND effect and return to its default value. MUTE: Press this key to turn mute on and off. SURROUND: Before operating this function, make sure the system is in the 2CH mode. Otherwise it will not function when the key is pressed. INPUT SEL: Use the key to operate 1-3 INPUT. MAIN: To increase / decrease master volume level LF: To increase I decrease left front volume level LR: To increase I decrease left rear volume level RF : To increase / decrease right front volume level RR: To increase / decrease right rear volume level SW: To increase / decrease subwoofer volume level C: To increase / decrease center volume level + I - : increase / decrease overall volume level CONTROL UNIT CONNECTIONS (BACK PANEL): WOOFER BACK PANEL f© © @ © © © □ LF IR cp* 1 9 c © © war © 8# © I 2 1).POWER 2).AC IN 3).5 CHANNEL OUTPUT 4).3 GROUPS INPUT TROUBLESHOOTING AND SUPPORT Problem Cause Remedy No Sound Speakers not properly connected incorrect input mode Amplifier is off/malfunction Check cables for short or open connections Select proper audio source (Digital or Analog) Check your amplifier Weak sound Volume control down Speak cable shorted or have broken strands Turn volume control up Check cables Buzzing sound Speaker cable (wire) short Check cable wiring No balance control Check balance control setting Adjust balance control Excessive Highs or lows Speaker out of circuit Check speaker - SPECIFICATIONS ©Remote Controller (DR-66) ©Satellite, Surround Speakers: • 2.5 Watts RMS each • 3" Full Range Speaker • 120Hz~20KHz Frequency Response • Impedance 4 Q • Dimensions:W96 X H120 X D98.5mm (3 3/4 X 4 3/4 X 3 7» inch) ©Center Speaker: • LED Display • Remote Control Receiver • Volume+,Volume —, ST-BY/MUTE Controls • 2.5 Watts RMS • 3” Full Range Speaker • 120Hz~20KHz Frequency Response • Impedance 4 Q • Dimensions:W200 X H120 X D105.5mm ( 7 7/8X 4 3/4 X4 1/8 inch) ©Subwoofer: • AV Input: Input 1: G9 to 6-RCA, RCA to RCA, stereo to stereo Input 2(Analog): stereo RCA X 2, RCA to RCA, stereo to stereo Input 3(Analog): stereo RCA X 2, RCA to RCA, stereo to stereo • Output: RCA:FL, FR, RL, RR Channels & stereo: CEN Channel • 12.5 Watts RMS • 4" Woofer Speaker • 50 Hz~2KHz L. F. E. • Impedance 4 Q • Power switch • Dimensions: W260 X H150 X D240mm (IO1/4 X 57/8 X 9 1/2 inch) RÎSK Of ELECTRIC SHOCK DO NOT OPEN A CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK. 00 NOT REMOVE COVER OR BACK NO USER—SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION PILOT LAMP SOLDERED IN PLACE. TO REDUCE. THE RISK OF ELECTRIC SHOCK. REFER TO QUALIFIED SERVICE PERSONNEL. A Attention, presence of dangerous voltage located within enclosure. Do not install this equipment in a confined space such as a book case or similar unit. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. The secondary switch does not disconnect the apparatus mains. Attention, consult instruction manual for important operating and maintenance (servicing)...