For stubborn food residue, use a degreaser and fiber or brass cleaning brush. Dry immediately using a soft cloth or paper towels. Cleaning Heat Distribution Plate: Heat distribution plates should be cleaned whenever food or grease drippings accumulate to reduce the chance of flare-ups. Wash heat distribution plates with a mild detergent and rinse with hot water. Use a degreaser and fiber or brass cleaning brush to remove stubborn food residue. Do not use a wire brush or metal scraper on porcelai

These steps should be performed after the grill has been assembled and prior to each use. DO NOT operate this grill until you have read and understand ALL of the warnings and instructions in this manual. E • Ensure that the grill is properly assembled. • Inspect the gas supply hose for burns, chaffing, kinks, and proper routing before each use. If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior the grill being used. • Leak check all gas connection

AVISO PARA EL INSTALADOR: ENTREGUE ESTAS INSTRUCCIONES AL PROPIETARIO DE LA PARRILLA PARA REFERENCIA FUTURA. AVISO PARA EL INSTALADOR: ENTREGUE ESTAS INSTRUCCIONES AL PROPIETARIO DE LA PARRILLA PARA REFERENCIA FUTURA. Universal Natural Gas Conversion Kit Equipo Universal de Conversion a Gas Natural PROFESSIONAL INSTALLATION MANUAL MANUAL DE INSTALACION PROFESIONAL CONVERTS THE FOLLOWING CHARMGLOW GRILLS FROM PROPANE TO NATURAL GAS: MODEL NUMBERS 810-7405-S, 810-8500-S, 810-8530-S, 810-8532-S, 81

AVIS A L’INSTALLATEUR: REMETTRE CETTE NOTICE AU PROPRIETAIRE POUR QU’IL PUISSE S’Y REFERER PLUS TARD. WARNING / AVERTISSEMENT HAZARDOUS EXPLOSION MAY RESULT IF THESE WARNINGS AND INSTRUCTIONS ARE IGNORED. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL TO AVOID PERSONAL INJURY, INCLUDING DEATH OR PROPERTY DAMAGE. UNE EXPLOSION DANGEREUSE RISQUE DE SE PRODUIRE SI CES AVERTISSEMENTS ET INSTRUCTIONS SONT IGNORES. LIRE ET RESPECTER TOUS LES AVERTISSEMENTS ET INSTRUCTIONS DE CETTE NOTICE

. . . . . . . . . . . . . . . . . . . . 16 Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17–18 Parts List and Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19–24 Grilling Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49–50 Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover DANGER: Indicates an imminently hazardous situ

NOTE: If burner does not light or flame is too low, you may have spider or other insect blockage in burner, or the flow limiting device has been activated. See "Burner Assembly/Maintenance" under Proper Care and Maintenance, or "Regulator Resetting Procedure" under Connecting LP Cylinder and Hose/Regulator to Grill. MATCH LIGHTING THE SIDE BURNER: 1. Open the lid to the side burner before lighting. 2. Turn the burner control knob to "OFF”. 3. Strike and carefully place a match approximately 1/2"

2. After grill is completely assembled, make sure natural gas supply valve is “OFF” and then connect natural gas hose to socket. Push sleeve back on socket (Figure B) and insert plug until sleeve snaps forward, locking plug into socket. Be sure to leak test these connections prior to use. Insert cover when hose is disconnected Pipe nipple Quick-disconnect coupling Plug Sleeve Natural gas supply Hose (Figure A) Supply valve (Figure B) Push sleeve back to attach Socket Natural gas supply Hose Supp

Igniter Wire Hose / Regulator Nuts CAUTION! Some parts may contain sharp edges. Wear protective gloves if necessary. NOTE: Make sure all control knobs are in the off position, LP tank valve is closed and tank is disconnected from regulator and removed from grill. Step 1 Remove hose / regulator from side burner valve and main burners manifold by unscrewing hose / regulator nuts. Remove igniter wire from electrode. Step 2 Remove control knobs and bezels from main control panel. Set aside for later

Save instructions for future reference. • Do not use the side burner when using a rotisserie. • When using an AC current rotisserie, it must be electrically grounded in accordance with local codes, or in the absence of local codes: • In the US: The National Electrical Code – ANSI-NFPA No. 70 – Latest Edition • In Canada: the Canadian Electrical Code – CSA C22.1 • The Rotisserie is equipped with a three pronged plug for your protection against electrical shock. This plug should be plugged directl

This is not to be confused with rust and is not a product defect. Machine oils used in the manufacturing process of stainless steel as well as cooking oils and a dirty grill lid can also encourage discoloration if the lid is not cleaned prior to grill use. After your grill is assembled, remove the protective PVC film from your grill lid and use a stainless steel cleaner and soft cloth to remove residual adhesive and oils from the inside and outside of your grill lid. Never use abrasive cleaners