Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Capital Cooking Dateigröße: 13.06 mb Dateiname: Unterrichtssprache:

If any of these conditions exist, check if the air shutter or burner ports are blocked by dirt, debris, spider webs, etc. and proceed with air shutter adjustment. The amount of air which is pulled through a burner is governed by a sheetmetal cup called the air shutter located at the inlet of the burner It is locked in place by a set screw which must be loosened prior to lighting the burner for adjustment. The air shutter adjustment screws are accessible with a screwdriver. Remove the burner by pulling up as shown in the figure above. Loosen the lock screw of the air shutter. Make certain that the burners are sitting properly on the orifices and light the burners. To adjust grill burner flame, be advised to adjust according to the following directions, also be careful as the burner may be very hot. If the flame is yellow indicating insufficient air, turn the air shutter counter-clockwise to allow more air to the burner. If the flame is noisy and tends to lift away from the burner, indicating too much air, turn the air shutter clockwise, until stable blue flame is obtained. PAGE 7 INSTALLERS's FINAL CHECK LIST CHECK WHEN COMPLETE □ Specified clearances maintained to combustibles □ All internal packaging has been removed □ All PVC protective coating has been removed □ Knobs turn freely □ Burners are sitting properly □ Each burner lights satisfactorily, individually or with adjacent burner □ Air shutter adjusted and locked in position □ Pressure regulator connected and set for 10" W.C. L. P. gas or 4.0" natural gas □ Unit tested and free of leaks □ User informed of gas supply shut off valve location INSTALLING THE BATTERY The battery is located behind the valve panel. It is attached by a magnetic strip. Reach behind the panel and remove the battery unplug old battery and replace with new one. Reinstall battery behind control panel. PAGE 8 BUILT-IN SPECIFICATIONS BUILT-IN SPECIFICATIONS FOR PRO-3 AND PRO-4 SERIES BBQ's CAUTION: USE ONLY IN NON-COMBUSTIBLE ENCLOSURES The appliance and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2" PSIG(3.5 kPa.). The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2" PSIG(3.5 kPa.). The installation of this appliance must conform with local codes or, in the absence of local codes, to the national fuel gas code, ANSI Z223.1a-1998. Installation in Canada must be in accordance with the Standard Can1-b149.1 and/or.2 (installation code for gas burning appliance and equipment) and local codes. NOTE: If the island has a backsplash, then the MINIMUM clearence between the bbq back and the backsplash must be 3" for lid to open freely completely. DO NOT INSTALL THE GRILL IN COMBUSTIBLE ENCLOSURES!! PAGE 9 PARTS LIST PRO-3 PRO-4 ITEM P/NUMBER NAME ITEM P/NUMBER NAME 1 10826-PA FRONT PANEL W/A PRO-3 1 10826-P4-PA FRONT PANEL W/A PRO-3 2 10822-02 TOP LID W/A PRO-3 2 10822-P4 TOP LID W/A PRO-4 3 86009 MANIFOLD FOR PRO-3 3 86003-P4 MANIFOLD FOR PRO-4 4 82417-01 9 VOLT IGNITER 3 82417-01 9 VOLT IGNITER 5 10873 DRIP TRAY 5 10873 DRIP TRAY 6 82200 LP GAS REGULATOR 6 82200 LP GAS REGULATOR 7 82203 NATURAL GAS REGULATOR 7 82203 NATURAL GAS REGULATOR 8 10852-02 FIRE BOX W/A PRO-3 8 10852-P4 FIRE BOX W/A PRO-4 9 80010 WARMING RACK 9 80010 WARMING RACK 10 80000-02 S/S GRILL RACKS 10 80000-02 S/S GRILL RACKS 11 xxxxx XXXXXXXXX 11 80000-04 CENTER GRILL RACK 12 10830 RADIANT 12 10830 RADIANT 13 10875 HEAT SHIELD 13 10875 HEAT SHIELD 14 81304-02 BEZEL 14 81304-02 BEZEL 15 10018-09 HANDLE TUBE 15 10018-12 HANDLE TUBE PRO-4 16 81000 HANDLE END CAP 16 81000 HANDLE END CAP 17 83002 KNOB 17 83002 KNOB 18 87040-01 BATTERY 18 87040-01 BATTERY 19 82417-02 BATTERY WIRES 19 82417-02 BATTERY WIRES 20 82100 VALVE 20 82100 VALVE 21 10842 ELECTRODE HOLDER 21 10842 ELECTRODE HOLDER 22 10841 GAS COLLECTOR 22 10841 GAS COLLECTOR 23 82000 ELECTRODE BURNER 12" 23 82000 ELECTRODE BURNER 12" 24 82012-12 ELECTRODE BURNER 36" 24 82012-12 ELECTRODE BURNER 36" 25 82418 H.E. BBQ IGNITION SWITCH 25 82418 H.E. BBQ IGNITION SWITCH ROTISSERIE KITS SOLD SEPARATE 26 G3-RTSKT FOR ROTISSERIE KIT PRO-3 26 PRO-4-RTSKT FOR ROTISSERIE KIT PRO-4 PAGE 10 LIGHTING INSTRUCTIONS Turn all knobs to " OFF " position. Turn on the gas supply. Always keep your face and body away from the grill when lighting. Open the lid, push and turn the control knob to the "HI" position and immediately press the igniter button.You will hear a clicking sound. At the same time, the electrode will spark at the burner. It may be necessary to hold down the igniter button until the burner is lit. If it does not light in 4 seconds, turn the knobs to the " OFF " position and wait 5 minutes to allow any accumulated gas to dis...

Herunterladen

Geben Sie zwei Ziffern: