Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Electrolux Dateigröße: 653.48 kb Dateiname: Unterrichtssprache:

lations.lations.lations.lations.lations. Permanent Connection Permanent ConnectionPermanent ConnectionPermanent ConnectionPermanent ConnectionPermanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact Ensure that the hob supply cord does not come into contactEnsure that the hob supply cord does not come into contactEnsure that the hob supply cord does not come into contactEnsure that the hob supply cord does not come into contactEnsure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg. C. with surfaces with temperatures higher than 50 deg. C.with surfaces with temperatures higher than 50 deg. C.with surfaces with temperatures higher than 50 deg. C.with surfaces with temperatures higher than 50 deg. C.with surfaces with temperatures higher than 50 deg. C. electrolux 25 Wiring diagram Wiring diagramWiring diagramWiring diagramWiring diagramWiring diagram 26 electrolux Fault Finding Fault FindingFault FindingFault FindingFault FindingFault Finding Preliminary Electrical Systems Check Preliminary Electrical Systems CheckPreliminary Electrical Systems CheckPreliminary Electrical Systems CheckPreliminary Electrical Systems CheckPreliminary Electrical Systems Check Blue STARTSTARTSTARTSTARTSTART Isolate appliance and carry out: A:A:A:A:A: Earth Continuity check. Has inlet fuse blown? Carry out: C:C:C:C:C: Polarity check. Electricity supply should now be satisfactory. Carry out: D:D:D:D:D: Resistance to Earth check. Inlet wiring faulty. Rectify any fault. Isolate appliance and carry out: B:B:B:B:B: Insulation check. Rectify any fault including replacing fuses as necessary. NONONONONO YESYESYESYESYES SOCKETSOCKETSOCKETSOCKETSOCKET (face view)(face view)(face view)(face view)(face view) PLUG (with cover removed)PLUG (with cover removed)PLUG (with cover removed)PLUG (with cover removed)PLUG (with cover removed) Earth Wire Green/Yellow Neutral Wire Blue ( ) FUSE ( )E N L NONONONONO YESYESYESYESYES Brown Green Yellow Green Yellow Brown Blue electrolux 27 A. EARTH CONTINUITY CHECK A. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECKA. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight. B. INSULA B. INSULAB. INSULAB. INSULAB. INSULAB. INSULATION CHECK TION CHECKTION CHECKTION CHECKTION CHECKTION CHECK Appliance electrically disconnected, all switches ON. a) meter set on W (Ohms) x 1 scale. Test leads from L to N in appliance terminal block. If meter reads «0» then there is a short circuit. b) meter set on W (Ohm) x 100 scale. Repeat test with leads from L to E. If meter reads less than . (infinity) there is a fault. NOTE - Should it be found that the fuse has failed but no fault is indicated -a detailed continuity check (i.e. by disconnecting and checking each component) is required to trace the faulty component. It is possible that a fault could occur as a result of local burning/arcing but no fault could be found under test. However a detailed visual inspection should reveal evidence of burning around the fault. 28 electrolux Ignition System / Gas Ignition Ignition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas Ignition Ignitor does not spark NO NONONONONO YES YESYESYESYESYES Check gas supply at burner Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check earth continuity of appliance Check position of the electrode Check fitting of burners Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from the tip of each electrode to the terminals 1 to 4 on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check for breaks in the insulation of the HT leads Check continuity from ignition switches connector to ignitor unit Change the ignitor unit electrolux 29 Commissioning CommissioningCommissioningCommissioningCommissioningCommissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. • .......... 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from...

Herunterladen

Geben Sie zwei Ziffern: