Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Coleman Dateigröße: 5.05 mb Dateiname: Unterrichtssprache:

19-C Quick Disconnect Coupling 27ATTACHED TO THE FUEL SOURCE. WARNING This procedure MUST be performed OUTDOORS only! Be sure L.P. cylinder valve is closed. Attach to Grill. Read and follow directions on the cylinder and fuel hose safety tags. CAUTION In the connection process, the grill side of the connection will seal on the back-check in the valve, resulting in a slight resistance. The connection requires about one-half to three- quarters additional turn to complete the connection. To disconnect, turn counterclockwise. Tighten by hand only. DO NOT use tools. Connecting Type 1 L.P. Gas Cylinders 15 WARNING This procedure MUST be performed OUTDOORS only! Be sure L.P. cylinder valve is closed. Attach to Grill. Read and follow directions on the cylinder and fuel hose safety tags. CAUTION In the connection process, the grill side of the connection will seal on the back-check in the valve, resulting in a slight resistance. The connection requires about one-half to three- quarters additional turn to complete the connection. To disconnect, turn counterclockwise. Tighten by hand only. DO NOT use tools. Connecting Type 1 L.P. Gas Cylinders 15 1. Check that the cylinder valve is closed by turning the cylinder knob clockwise to a full stop. 2. Check that all the grill burner knobs are in the off position. 3. Remove the protective caps from the cylinder valve and coupling nut. NOTE: The coupling nut connects to the large outside threads on the valve outlet. 4. Hold the regulator in one hand and insert the nipple into the valve outlet. Be sure the nipple is centered in the valve outlet. Hand-tighten the coupling nut, taking care not to cross-thread the connection (see Fig. 15). 5. Turn the coupling nut clockwise, tighten to a full stop. If you cannot complete the final connection, disconnect the regulator and repeat steps 4 through 6. If you are still unable to complete the connection, DO NOT use this valve and regulator! 6. Check that the hose has no kinks or sharp bends and clears areas that will become hot during use. Never put strain on the hose where it joins a fitting. 7. BEFORE lighting grill, check all connections for leaks using the procedure as shown in Fig. 16 on pg. 28. Leak Testing Leak Testing (cont.) How to Check for Leaks 1. Make a soapy solution of equal parts mild liquid dishwashing detergent and water. 2. Turn off all burner control knobs. 3. Turn on fuel supply. Turn cylinder valve knob counterclockwise (right to left) one rotation. 4. Apply soap solution to connections indicated with arrows in Fig. 16. If bubbles appear at these areas, a leak is indicated. 16 Fixing A Fuel Leak • If you detect a leak: 1. Turn off the fuel supply. Push in and turn on control knobs to release pressure in hose, then turn the control knobs back to off. 2. Wash off soapy solutions with cold water and towel dry. 3. Stop a leak by tightening the loose joint, or by replacing the faulty part with a replacement part recommended by Coleman. DO NOT attempt to repair the cylinder valve if it should become damaged; the cylinder MUST be replaced. 4. If you are unable to stop a leak, shut off the gas supply at the cylinder valve. Remove the cylinder from the grill. Call a gas appliance serviceman or L.P. gas dealer. DO NOT use grill until the leak is corrected. • When to test for leaks: 1. Perform a leak test each time the gas supply cylinder is connected to the regulator. Leak test anytime a part of the gas system is replaced. 2. Perform a leak test at least once each year whether the L.P. gas supply cylinder has been disconnected or not. 3. Have a dealer check the cylinder for deterioration after 12 years, according to DOT regulations. Immediately replace cylinder if any deterioration is found. DANGER TO PREVENT FIRE OR EXPLOSION HAZARD: • NO SMOKING. DO NOT use or permit sources of ignition in the area while doing a leak test. • Perform leak tests outdoors only. • NEVER perform a leak test with fire or flame. 28 CAUTION Inspect the gas supply hoses before each use. If there are cuts, damage, excessive abrasion or wear, replace the hoses prior to operating the appliance. During assembly of grill and when attaching or replacing the L. P. gas cylinder, insure that all gas supply hoses are free of kinks and/or damage and are at least 3" away from hot surfaces such as the grill housing. Use only hose replacements specified in the parts list. 1. Regularly check burner venturi tubes for blockage from an insect nest. Read “Cleaning the Venturi” on pg. 32 and “Troubleshooting” on pg. 33. 2. Check that all burner venturi [H] are set over the valve outlets [J] correctly. The valve orifice [K] must be inside the venturi. (Fig. 17) 3. Inspect the gas supply hoses before each use. Hoses can be burned or chafed if they are routed improperly. See that hoses have no kinks, sharp bends or tension. Insure that hoses are at least 3 inches away from any hot surface. 4. Use only the gas specified. 5. Keep the grill on a level surface. 6. Keep greas...

Herunterladen

Geben Sie zwei Ziffern: