Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
4-B 4-B. Assemble one Door Magnet to the Base with two Screws (TN). Door Magnet TN (x2) Hardware shown actual size (TN) M6 x 15mm Screw (2) Qty. 11 .... Assemble two Spacers to the Top Panel. .... Assemble the Top Panel to the Grill Cart. 5-A 5-A. Assemble the two Spacers to the Top Panel with four Screws (TN). Hardware shown actual size TN (x4) Top Panel Step 5 (TN) M6 x 15mm Screw (11) Qty. Spacer (x2) (with flange up) 5-B 5-B. Assemble the Top Panel to the Grill Cart with seven Screws (TN). TN (x7) Top Panel 6-A 6-A. Carefully place the Firebox onto the Cart Assembly. Do not damage the fuel hoses. They must be routed through the large hole in the top panel. See Step 6-B. Firebox Grill Cart Step 6 Hardware shown actual size (TN) M6 x 15mm Screw (4) Qty. (DY) M6 Flat Washer (4) Qty. View of Grill from Rear .... Assemble Firebox to the Grill Cart. .... NOTE: A second person is needed when aligning the Firebox to the Grill Cart. 12 6-B View of Grill from Front 6-B View of Grill from Front 6-B. While lowering the Firebox, route the fuel hoses through the large hole in the top panel. 6-C 6-C. Fasten the front side of the Firebox to the Grill Cart with two Flat Washers (DY) and two Screws (TN). 6-D 6-D. Fasten the back side of the Firebox to the Grill Cart with two Flat Washers (DY) and two Screws (TN). DY (x2) TN (x2) TN (x2) DY (x2) View of Grill from Rear View of Grill from Front 13 .... NOTE: The Grill Lid should be opened for Steps 7 and 8. .... Assemble Right Side Table to the Grill. 7-A Right Side Panel Step 7 FIREBOX Right Side Table 7-A. Raise the Grill Lid. .... Place the Right Side Table against the Firebox and on top of the Right Side Panel. 7-B 7-B. Align two Keyhole Slots in the Right Side Table over two pins on the side of the Firebox (see Fig. 7-C). .... Assemble two screws (TN) through the back flange of the Right Side Table into the back flange of the Right Side Panel (see Fig. 7-C). .... Assemble two screws (TN) through the front flange of the Right Side Table into the front flange of the Right Side Panel (not illustrated). 7-C TN Align Slot with Pin Hardware shown actual size (TN) M6 x 15mm Screw (5) Qty. (UO) M6 Locking Hex Nut (1) Qty. (DY) M6 Flat Washer (1) Qty. Right Side Table 14 7-D TN DY UO View of Grill from Rear 15TN DY UO View of Grill from Rear 15 7-D. Assemble one Screw (TN), one Flat Washer (DY) and one Locking Hex Nut (UO) through the Firebox into the Right Side Table. • ....Tighten all fasteners. .... Assemble Left Side Burner to the Grill. Step 8 Hardware shown actual size (TN) M6 x 15mm Screw (5) Qty. (UO) M6 Locking Hex Nut (1) Qty. (DY) M6 Flat Washer (1) Qty. 8-A Left Side Burner Table 8-A. Place the Left Side Burner Table against the Firebox and on top of the Left Side Panel. 8-B Left Side Burner Table 8-B. Align two Keyhole Slots in the Left Side Burner Table over two pins on the side of the Firebox (see Fig. 8-C). .... Assemble two screws (TN) through the back flange of the Left Side Burner Table into the back flange of the Left Side Panel (see Fig. 8-C). .... Assemble two screws (TN) through the front flange of the Left Side Burner Table into the front flange of the Left Side Panel (not illustrated). 8-C Firebox Left Side Panel TN Align Slot with Pin 16 8-D 8-E UO View of Grill from Rear TN DY 178-D 8-E UO View of Grill from Rear TN DY 17 8-D. Assemble one Screw (TN), one Flat Washer (DY) and one Locking Hex Nut (UO) through the Firebox into the Left Side Burner Table. • ....Tighten all fasteners. ........ Hardware shown actual size Step9Hardware shown actual size Step9 Fasten the Rear Trim Plate to the Grill Cart. NOTE: On some models, the Rear Trim Plate is pre- installed by the factory. (VP) Self Tapping Screw (2) Qty. 9-A 9-A. Fasten the Rear Trim Plate to the Firebox with two Screws (VP). ....Tighten all fasteners. Firebox VP (x2) Rear Trim Plate VP 18 9-B 9-B. View showing Rear Trim Plate properly installed. Rear Trim Plate 10-A Hardware shown actual size (XR) M5 x 15mm Flat Head Screw (8) Qty. Right Door Step 10 (BW) M5 Hex Nut (2) Qty. Left Door 10-B. Fasten the Right Door to the Grill Cart with four Flat Head Screws (XR). Use one Locking Hex Nut (BW) on the top location only. .... Repeat Step 10-B to attach the Left Door. .... Tighten all fasteners. 10-B XR (x4) BW (x1) 10-C. Squeeze the Tool Hook to slip into the mounting brackets. 10-C Tool Hook 10-D EZ (x2) Right Door 10-D. Fasten one Door Handle to the Right Door with two Screws (EZ). Repeat Step 10-D to assemble one Door Handle to the Left Door. .... Tighten all fasteners. Door Handle (EZ) M4 X 5mm Screw (4) Qty. .... Fasten both Left and Right Doors to the Grill Cart. .... Attach the Tool Hook to the Right Door. .... Fasten the Door Handles to the Doors. .... NOTE: M4 x 5mm Screws (EZ) are factory installed into the Handles. 19 Tool Hook Step 11 • ....Install four Heat Tents™. • ....Install four Cooking Grates. • ....Install the Warming Rack. 11-B Heat Tents™ 11-B. Install four Heat Tents™ over the Bur...
Dieses Handbuch ist für folgende Modelle:Konvektionsöfen - 5310 (5.05 mb)