Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Lenmar Enterprises, modell 94088

Hersteller: Lenmar Enterprises
Dateigröße: 728.03 kb
Dateiname: 86430767-79be-4136-93f4-6561172b15c3.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

(h) See operating instructions for length of charge information. 16. Follow these steps when battery is outside vehicle. A spark near battery may cause battery explosion. To reduce risk of a spark near battery: (a) Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger diameter than NEGATIVE (NEG, N, -) post. (b) Attach at least a 24-inch-long 6-gauge (AWG) insulated battery cable to NEGATIVE (NEG, N, -) battery post. Place the other end of this cable on a dry insulating surface, such as a piece of dry wood. (c) Connect POSITIVE (RED) charger clip to POSITIVE (POS, P, +) post of battery. (d) Position yourself and free end of cable as far away from battery as possible- then connect NEGATIVE (BLACK) charger clip to free end of the cable. (e) Do not face battery when making final connection. (f) When disconnecting charger, always do so in the reverse sequence of connecting procedure and break first connection while as far away from the battery as practical. (g) A marine (boat) battery must be removed and charged on shore. To charge it on board requires equipment specially designed for marine use. SAVE THESE INSTRUCTIONS SKU 94088 For technical questions, please call 1-800-444-3353. Page 5 Specific Safety Rules for the Battery Charger Specific Safety Rules for the Battery Charger . Maintain labels and nameplates on the Battery Charger.These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Always wear safety impact eye goggles and heavy work gloves when using the Battery Charger. Using personal safety devices reduce the risk for injury. Safety impact eye goggles and heavy work gloves are available from Harbor Freight Tools. 3. Maintain a safe working environment. Keep the work area well lit. Make sure there is adequate surrounding workspace. Always keep the work area free of obstructions, grease, oil, trash, and other debris. Do not use a power tool in areas near flammable chemicals, dusts, and vapors. Do not use this product in a damp or wet location. 4. Avoid unintentional starting. Make sure you are prepared to begin work before plugging Always unplug the Battery Charger from its electrical outlet before connecting its cables to a battery, or performing any inspection, maintenance, or cleaning procedures. 6. Keep extension cord off wet ground and away from water. 7. Use this Battery Charger with lead/acid batteries only. When charging a maintenance- free battery, always monitor the progress of the charge. Do not over charge a maintenance- free battery. 8. Do not attempt to charge non-rechargeable or defective batteries. 9. Keep connections and cable clamps clean and free from corrosion. 10. Never simultaneously charge several batteries. 11. Do not discard used batteries in the trash. Properly recycle according to local environmental codes. 12. Do not attempt to charge a 6 volt battery. 13. People with pacemakers should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker. 14. This product contains or, when used, produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code § 25249.5, et seq.) 15. Risk of Explosion! • If you detect gas, do not switch off the unit. Do not disconnect the charging clamps. Immediately ventilate the room by opening windows and doors. Do not switch on an electrical fan.When the air has cleared of gas, unplug the unit from the electrical outlet. • Charge the battery in a well-ventilated area. • To prevent sparking due to electrostatic discharge, never wear clothes made of synthetic materials when charging the battery. • Avoid creating or working around any flames or sparks; flames or sparks can ignite the gasses caused by charging and cause an explosion. 2. the Battery Charger. 5. SKU 94088 For technical questions, please call 1-800-444-3353. Page 6 ASSEMBLY INSTRUCTIONS 1. When unpacking, check to make sure that the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. 2. This product comes preassembled. No additional assembly is necessary. OPERATING INSTRUCTIONS Warning: Do not overcharge maintenance- free batteries. Do not try to start the engine with the Battery Charger connected to the battery. 1. FOLLOW ALL CONNECTION PRECAUTIONS AS OUTLINED ON PAGES 4 & 5 OF THIS MANUAL. Place the Battery Charger and battery in a well- ventilated area. 2. Determine the voltage of the battery from the battery labels.This device is intended for use on 12 Volt batteries only 3. Push the Charge Rate Switch to the desired amperage. 4. If charging a battery while in a vehicle, leave the hood open and do not leave the charger unattended. Separate the charger and battery as much as possible. 5. I...