Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: DeWalt Dateigröße: 3.92 mb Dateiname: 5ce03e61-90fd-48fd-abfb-003f2679e489.pdf Unterrichtssprache:

If either of these is the desired angle, retighten the lever (J) by lowering it. If you desire another angle, continue tilting the shoe until the pointer aligns with the desired mark. Retighten lever (J) by lowering it. Shoe Adjustment for 90° Cuts WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from battery pack before making any adjustments or removing/installing attachments or accessories. IF ADDITIONAL ADJUSTMENT IS NEEDED (FIG. 12) 1. Adjust the saw to 0° bevel. 2. Retract blade guard. Place the saw on blade side. 3. Loosen bevel adjustment lever or knob (J). Place a square against the blade and shoe to adjust the 90° setting. 4. Turn the adjustment screw (K) on the underside of the shoe until the blade and the shoe are both in flush contact with the square. Retighten the bevel adjust lever or knob. 5. Confirm the accuracy of the setting by checking the squareness of an actual cut on a scrap piece of material. FIG. 12 K FIG. 13 Kerf Indicator The front of the saw shoe has a kerf indicator for vertical and bevel cutting. This indicator enables you to guide the saw along cutting lines penciled on the material being cut. The indicator lines up with the left (outer) side of the saw blade, which makes the slot or “kerf” cut by the moving blade fall to the right of the indicator. Guide along the penciled cutting line so that the kerf falls into the waste or surplus material. English English FIG. 14 DO support board or panel NEAR the cut. SUPPORT FIG. 15 DON’T support board or panel AWAY from the cut. Workpiece Support WARNING: It is important to support the work properly and to hold the saw firmly to prevent loss of control which could cause personal injury. Figure 13 illustrates proper hand support of the saw. Maintain a firm grip with both hands on the saw and position your body and arm to allow you to resist kickback if it occurs. Figure 13 shows proper sawing position. Note that hands are kept away from cutting area. To avoid kickback, DO support board or panel NEAR the cut (Fig. 14). DON’T support board or panel away from the cut (Fig. 15). Place the work with its “good” side – the one on which appearance is most important – down. The saw cuts upward, so any splintering will be on the work face that is up when you cut it. Cutting Place the wider portion of the saw shoe on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Figure 13 illustrates the RIGHT way to cut off the end of a board. Always clamp work. Don’t try to hold short pieces by hand! Remember to support cantilevered and overhanging material. Use caution when sawing material from below. 15 Be sure saw is up to full speed before blade contacts material to be cut. Starting saw with blade against material to be cut or pushed forward into kerf can result in kickback. Push the saw forward at a speed which allows the blade to cut without laboring. Hardness and toughness can vary even in the same piece of material, and knotty or damp sections can put a heavy load on the saw. When this happens, push the saw more slowly, but hard enough to keep working without much decrease in speed. Forcing the saw can cause rough cuts, inaccuracy, kickback, and over-heating of the motor. Should your cut begin to go off the line, don’t try to force it back on. Release the switch and allow blade to come to a complete stop. Then you can withdraw the saw, sight anew, and start a new cut slightly inside the wrong one. In any event, withdraw the saw if you must shift the cut. Forcing a correction inside the cut can stall the saw and lead to kickback. IF SAW STALLS, RELEASE THE TRIGGER AND BACK THE SAW UNTIL IT IS LOOSE. BE SURE BLADE IS STRAIGHT IN THE CUT AND CLEAR OF THE CUTTING EDGE BEFORE RESTARTING. As you finish a cut, release the trigger and allow the blade to stop before lifting the saw from the work. As you lift the saw, the spring-tensioned telescoping guard will automatically close under the blade. Remember the blade is exposed until this occurs. Never reach under the work for any reason. When you have to retract the telescoping guard manually (as is necessary for starting pocket cuts) always use the retracting lever. NOTE: When cutting thin strips, be careful to ensure that small cutoff pieces don’t hang up on inside of lower guard. RIPPING (FIG. 16) Ripping is the process of cutting wider boards strips – cutting grain lengthwise. Hand guiding is more difficult for this type of sawing and the use of a rip fence is recommended. INSTALL RIP FENCE IN THIS DIRECTION FIG. 16 INSTALL RIP FENCE IN THIS DIRECTION FIG. 16 POCKET CUTTING (FIG. 17) WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from battery pack before making any adjustments or removing/installing attachments or accessories. WARNING: Never tie the blade guard in a raised position. Never move the saw backwards when pocket cutting. This may cause ...

Herunterladen

Geben Sie zwei Ziffern: