Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Switching the childproof lock on and off The hob must be switched off. To switch on: Touch the D symbol for approx. 4 seconds. The display light above the D symbol lights up for 10 seconds. The hob is locked. To switch off: Touch the D symbol for approx. 4 seconds. The hob is unlocked. Automatic childproof lock This function automatically activates the childproof lock every time you switch the hob off. Switching on and off You can find out how to switch the automatic childproof lock on and off in the Basic settings section. Automatic time limit If a hotplate has been switched on for a long time without the When the time limit is activated depends on the heat setting setting being changed, the automatic time limit is activated. selected (1 to 10 hours). The hotplate stops heating. ” ‰ and the •/oe residual heat indicator flash alternately on the hotplate display. The display goes out when you touch any control. You can make new settings. Basic settings Your appliance has various basic settings. You can adapt these settings to your needs. Display Function ™‚ Automatic childproof lock ‹ Switched off.* ‚ Switched on. ™. Audible signal ‹ Confirmation signal and operation error signal are switched off. ‚ Only the operation error signal is switched on. . Only the confirmation signal is switched on. „ Confirmation signal and operation error signal switched on.* ™. Activation of the filament circuits ‹ Switched off. ‚ Switched on. . Last setting before the hotplate was switched off.* ™S Time for selecting the hotplate ‹ Unlimited: The last selected hotplate can always be adjusted without having to select it again.* ‚ Once you select a hotplate, you have 10 seconds to adjust it, after which you will have to select it again in order to be able to adjust it. ™‹ Reset to basic setting ‹ Switched off.* ‚ Switched on. * Basic setting Changing the basic settings The hob must be switched off. 1. Switch on the hob. 2. Within the next 10 seconds, touch the D symbol for 4 seconds. ™ and ‚ flash alternately in the lower display and ‹ lights up in the upper display. 3. Touch the D symbol repeatedly until the desired indicator appears in the lower display. 4. Touch the + or -symbol repeatedly until the desired setting appears in the upper display. 5. Touch the D symbol for 4 seconds. The setting is activated. Switching off To exit the basic setting, switch off the hob with the main switch and make new settings. Cleaning and care The information in this section provides help on how best to care for your hob. Suitable maintenance and cleaning products can be purchased from the after-sales service or in our e-Shop. Ceramic Clean the hob after each use. This will prevent spills from burning onto the ceramic. Only clean the hob when it has cooled down sufficiently. Use only cleaning agents which are suitable for glass ceramic. Follow the cleaning instructions on the packaging. Never use: ¦ Undiluted washing-up liquid ¦ Detergent intended for dishwashers ¦ Scouring agents ¦ Harsh cleaning agents such as oven spray or stain remover ¦ Abrasive sponges ¦ High-pressure cleaners or steam jet cleaners Ground-in dirt can be best removed with a glass scraper, available from retailers. Please note the manufacturer's instructions. You can also obtain a suitable glass scraper from our after- sales service or from the e-Shop. Using special sponges to clean glass ceramic achieves great cleaning results. Hob surround To prevent damage to the hob surround, observe the following instructions: ¦ Use only hot soapy water. ¦ Wash new sponge cloths thoroughly before use. ¦ Do not use any sharp or abrasive agents. ¦ Do not use the glass scraper. Rectifying faults Malfunctions often have simple explanations. Please read the following notes before calling the aftersales service. Display Fault Measure Blank There is no power supply. Check the household fuse for the appliance. Check whether there is a power cut by trying other electronic appliances. All displays The controls are damp or an object is Dry the controls or remove the object. flash resting on them. ”. The electronics have overheated and Wait until the electronics have cooled down sufficiently. Then touch a con- have switched off the corresponding trol for the hotplate. hotplate. ”… The electronics have overheated and Wait until the electronics have cooled down sufficiently. Then touch any have switched off all hotplates. control. ”‰ The hotplate was in operation for too You can switch the hotplate back on again immediately. long and has switched itself off. If - flashes in the hotplate indicators: If -flashes in the hotplate indicators when the appliance is connected to the mains or following a power cut, the electronics are malfunctioning. To acknowledge the fault, briefly cover the controls with your hand. After-sales service Our after-sales service is there for you if your appliance should need to be repaired. We are committed fo find the best solution also in order to avoid an unnecessary call-...