Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
1) Loosen the hinge cover screws and remove the cover. Remove connection wires, if any, except for the earth line. 2) Remove keeper by rotating it clockwise ( ) and then remove the upper hinge by lifting it up ( ). 3) Remove the refrigerator compartment door by lifting it up. Remove the refrigerator compartment door Connection wires Upper hinge Keeper . . Lower hinge Pass the refrigerator laterally through the access door as illustrated to the right. Pass the refrigerator Door replacement Once the fridge is through the access door, remount the fridge doors by following the door removal instructions in reverse. Feed water pipe installation (Dispenser model only) Before installation .Automatic ice maker operation needs water pressure of 147~834kPa (1.5~8.5kgf/cm2) (The pressure is correct when an instant paper cup (180cc) is filled in 3 sec.). .If water pressure does not reach the rating 147kPa(1.5kgf/cm2) or below, it is necessary to purchase a separate pressure pump for normal automatic icing and cool water feed. .Keep the total length of the feed water pipe tube within 8m and be careful that the tube does not bend. If the tube is 8m or longer it may cause water feed problems owing to the drain water pressure. .Install the feed water pipe tube at a place free from heat. .Connect to drinking water supply only. .Refer to instructions with water filter kit for installation. Warning Door height adjustment Level the door by inserting flat( - type) driver into the groove of the left height adjusting screw and rotate it clockwise ( ). If the freezer compartment door is lower than the refrigerator compartment door . Height difference Height difference Left height adjustment screw Level the door by inserting flat( - type) driver into the groove of the left height adjusting screw and rotate it clockwise ( ). If the freezer compartment door is higher than the refrigerator compartment door . Height difference Height difference Right height adjustment screw Starting When your refrigerator is first installed, allow it to stabilize at normal operating temperatures for 2-3 hours prior to filling it with fresh or frozen foods. If operation is interrupted, wait 5 minutes before restarting. Adjusting the temperature and functions *Non dispenser model - Type 1 Refreshment Centre button (Optional) Refreshment Centre (Optional) Function display board NOTE • Your model may not include every option. •The control display is touch operated. Excessive moisture on the display panel may result in its malfunction. Please keep the display panel dry and clean. *Non dispenser model - Type 2 Refreshment Centre button (Optional) Refreshment Centre (Optional) Function display board Display Power Saving Mode NOTE • Your model may not include every option. • The control display is touch operated. Excessive moisture on the display panel may result in its malfunction. Please keep the display panel dry and clean. *Dispenser model - Type 1 Refreshment Centre button (Optional) Water/Ice output Dispenser push switch Refreshment Centre (Optional) Option Function display board Type-1 Type-2 NOTE • Your model may not include every option. • The control display is touch operated. Excessive moisture on the display panel may result in its malfunction. Please keep the display panel dry and clean. *Dispenser model - Type 3 Refreshment Centre button (Optional) Water/Ice output Dispenser push switch Refreshment Centre (Optional) Dispenser Lamp (hidden) Option Function display board Type-1 Display Power Saving Mode Type-2 NOTE • Your model may not include every option. • The control display is touch operated. Excessive moisture on the display panel may result in its malfunction. Please keep the display panel dry and clean. Dispenser use (on some model) . Choose from crushed ice, water, and cubed ice and depress the dispenser switch with a glass or other container. Crushed Ice Select crushed ice by pressing the selection button, which will be highlighted. Water Select water by pressing the selection button, which will be highlighted. Cubed Ice Select cubed ice by pressing the selection button, which will be highlighted NB : Please wait for 2-3 seconds before removing the cup from beneath the dispenser to ensure it has finished dispensing the ice or water. Door mounted automatic icemaker (on some model) Power Switch Feeler Arm . The icemaker automatically makes 6 cubes of ice at any one time, which equals approximately 50-60 cubes per day. These quantities, however, may vary according to climatic conditions. E.g. the duration and amount of times the refrigerator door is opened. . Icemaking stops when the ice storage bin is full. . If you don’t want to use the automatic icemaker, turn the icemaker switch to OFF. If you want to use automatic icemaker again, change the switch to ON. NOTE • The sound produced when the ice drops into the ice storage bin is normal, and is not caused by a defect. WARNING • Do not put your hands into the Ice maker during operation. You m...