Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Remove the lower cover by lifting upward, and remove clip, and then pull up the feed water tube while pressing area • shown in the figure to the right. Lower cover NOTE • If a tube end is deformed or abraded, cut the part away. Hinge cover 1) Removing the hinge cover by loosening the screws. Separate all connection wires except for the earth line after. Upper hinge Feed water tube Connection wires Earth line Upper hingeKeeper 2) Remove the keeper by rotating it counter clockwise () and then lifting the upper hinge up (). NOTE • When removing the upper hinge, be careful that the door does not fall forwards . 3) Remove the freezer compartment door by lifting it upward. This time, the door should be lifted enough for the feed water pipe tube to be completely pulled out. Lower hinge NOTE • Move the refrigerator compartment door passing through the access door and lay it down, but be careful not to damage the feed water pipe tube. 1) Loosen the hinge cover screws and remove the cover. Remove connection wire, if any, except for the earth line. 2) Remove keeper by rotating it clockwise () and then remove the upper hinge by lifting it up (• ). 3) Remove the refrigerator compartment door by lifting it up. Upper hinge Connection wires Keeper Lower hinge 6 Installation Installation Pass the refrigerator Before installation Warning Pass the refrigerator laterally through the access door as shown in the right figure. Door replacement Mount them in the reverse sequence of removal after they pass through the access door. Feed water pipe installation • Automatic ice maker operation needs water pressure of 147~834 kPa (1.5~8.5 kgf/cm2) (That is, an instant paper cup (180 cc) will be fully filled within 3 sec.). • If water pressure does not reach the rating 147 kPa (1.5 kgf/cm2) or below, it is necessary to purchase a separate pressure pump for normal automatic icing and cool water feed. • Keep the total length of the feed water pipe tube within 8 m and be careful for the tube not be bent. If the tube is 8 m or longer it may cause trouble in water feed owing to the drain water pressure. • Install the feed water pipe tube at a place free from heat. • Connect to potable water supply only. • Refer to instructions with water filter kit for installation. 7 Installation If the freezer compartment door is lower than the refrigerator compartment door If the freezer compartment door is higher than the refrigerator compartment door After leveling the door height Next Height adjustment Level the door by inserting flat ( -type) driver into the groove of the left height adjusting screw and rotate it clockwise (). Level the door by inserting flat ( -type) driver into the groove of the right height adjusting screw and rotate it clockwise (). The refrigerator doors will close smoothly by heightening the front side by adjusting the height adjusting screw. If the doors do not close correctly, performance may be affected. 1. Wipe off all dust accumulated during shipping and clean your appliance thoroughly. 2. Install accessories such as the ice cube box, cover evaporating tray, etc., in their proper places. They are packed together to prevent possible damage during shipping. 3. Connect the power supply cord (or plug) to the outlet. Don't double up with other appliances on the same outlet. 8 9 (hidden) Refreshment Center Function display board Display Power Saving Mode Refreshment Center Button Operation • Your model may not include every option. NOTE Starting When your refrigerator is first installed, allow it to stabilize at normal operating temperatures for 2-3 hours prior to filling it with fresh or frozen foods. If operation is interrupted, wait 5 minutes before restarting. Adjusting the temperatures and functions Operation Display power saving Freezer control Refrigerator control This function save the display power Press the FREEZER and EXPRESS FRZ. buttons simultaneously and hold them for 5 seconds until the Ding sounds. All LED/LCDs will then turn ON, then OFF. When the power saving mode is activated, the display will remain off until the next time the door is opened. Then, it will come on whenever a door is opened or a button is pressed and remain on for 20 seconds after the last door opening or button selection. To deactivate the power saving mode, press the FREEZER and EXPRESS FRZ. buttons simultaneously and hold them for 5 seconds until the Ding sounds. You can adjust temperature of and freezer room and refrigerator room. Freeze. Compartmen. temperatur. adjustmen. FREEZE. Settin. temperatur. Refrigerato. Compartmen. temperatur. adjustmen. REFRIGERATO. Settin. temperatur. . Whenever pressing button, setting is repeated in the order of (Weak) . (Middle Weak) . (Middle) . (Middle Strong) . (Strong). • The actual inner temperature varies depending on the food status, as the indicated setting temperature is a target temperature, not actual temperature within refrigerator. • Refrigeration function is weak in the initial time. Please ad...