Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
28 To Reverse the Doors Your fridge-freezer is designed with reversible doors,so that they may open from either the left or right hand side to suit your kitchen design. Precaution 1.Before reversing the door, first of all,you should take out food and accessories like shelves or trays which are not fixed in the fridge-freezer. 2.Use Torque Wrench or Spanner to fix or remove the bolt. 3.Do not lay the fridge-freezer down.This will cause problems. 4.Be careful not to drop the doors in disassembling or assembling. How to Reverse the Door 1.To separate the door handle 1 of the left side, separate the door cap 2 and unscrew the screw 3 in counterclockwise direction.Separate the door handle 4of the freezer in the same order. 14323256781019 2.After unscrewing the screw 6 of the right hinge cover on the top, separate the right hinge cover 5 5 to separate the connecting cable 9 .Separate the bolt 7 fixating the upper right hinge 8 , and carefully separate the refrigerator door 10 . Remove the left cover 19 . 3.After separating the upper left cap 11 of the separated refrigerator door 10 , carefully take off the top cap 12and pull the cable 13 to connect to the hole on the leftside. Set the separated top cap 12 at the regular position and set the cap 11 on the cable hole on the right side. Loosen the screw 3244 under the cold room door 10 , move it to the left of the stopper 3143 , and then connect it. 4.Use a sharp gimlet or knife to disconnect the cap 15from the cover front 14 , loosen the screw 16 , and then move the cable 18 to the left to be mounted. Disconnect the cable and the door switch 1440 from the disconnected cover front , swap the position of the disconnected cable 38 40 and door switch 38 with the cap 39 , mount them, fix them with the screw 16, and then install the cap 15 . 11 29 16151418384039 10124344 13 3132 Move the separated door handle to the right and fixate the screw on the right position to attach the door cap .Move the door cap on the right side to the left and attach it. Attach the freezer door handle in the same method as the refrigerator Loosen the bolt of the Hinge Middle , remove the Hinge Middle , and lift up the freezer door to separate it. (When separating the refrigerator door, separate the bush together.)Separate the hinge cover and set it on the separated part of middle hinge . After unscrewing the screw connected to the bottom cover connect the cover cap on the right side. Loosen the bolt connected to the lower hinge . Unscrew the screw fixating the door stopper at the Note Reversing the doors is not covered by the warranty. 1 3 2 41 2 41 41 3 2 3 2 30 21 25 26 21 20 21 24 5. 35 bottom of the freezer door ,and fixate it on the hole on the left side with the door stopper .and then ,move the upper cap to the right and cover it. 6. Set the separate lower hinge and put it in the bag,take out the lower left hinge of the bag and set the lower left hinge on the bottom hole of the left side of the freezer then tighten the bolt .After fixating the bottom cover at the regular position,align the freezer door on the pin of lower hinge to attach it properly. Turn over the separated middle hinge and sheet hinge to assemble them. And set the bush and washer together to tighten the bolt . (When tightening the bolt, be careful not to cause an scratch on the cap decor on top of the freezer door). 8. door handle 1 . 7. 30 24 20 21 22 35 23 21 45 27 20 25 30 33 26 25 30 31 32 37 36 7 6 42 9 10 43 44 27 28 After assembling the door by aligning the hinge hole on the bottom of the refrigerator door and the pin of the middle hinge , take out the upper left hinge cover and the left hinge of the bag, After connecting the cable , tighten the bolt to screw the screws to the left hinge cover Take the right cap out of the bag and clean up the wire,...
Dieses Handbuch ist für folgende Modelle:Kühlen - GC-B419WEQK (5.26 mb)
Kühlen - GC-B419WLQK.APVQCIS (5.26 mb)
Kühlen - GC-B419WNQK (5.26 mb)
Kühlen - GC-B419WNQK.APIQCIS (5.26 mb)