Login:
Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Anleitung Samsung, modell RS22JLSG

Hersteller: Samsung
Dateigröße: 2.08 mb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Dieses Gerät hat auch andere Anweisungen:
Kühlen - RS22JLSG (2.02 mb)de

Anleitung Zusammenfassung


When you turn clockwise ( ), the door goes up. . WRENCH Adjustment part Adjustment part . NUT . BOLT . WRENCH . NUT . WRENCH . NUT . WRENCH . NUT . BOLT . WRENCH . BOLT . WRENCH . BOLT . BOLT . BOLT Please open the doors and adjust the doors as follows: 1) Release the nut () on the lower hinge until the upper end of the bolt (.). When you release the nut(), use enclosed hex wrench (.) to turn the bolt(.) a little counter clockwise NOTA to make the nut() loose with your fingers. NOTE NOTA CHECKING THE WATER DISPENSER LINE (OPTIONAL) 1) In order to operate the ice maker properly, water pressure of 1.4 ~ 10 kgf/cm2 is required. In this range a 100 cc paper cup can be filled in 10 seconds. 2) The water filter removes particles. It does not sterilize or destroy any micro-organisms. 3) If the refrigerator is installed in an area with low water pressure (below 1.4kgf/cm2), you should install a booster pump to compensate for the low pressure. 4) Ensure the water storage tank inside the refrigerator is preperly filled initially. Push the water dis penser lever until the water runs from the outlet. NOTE A universal water supply kit is available at extra cost from your dealer. The refrigerator manufacturer recommends using a water supply kit containing copper tubing. Checking the Parts Purifier (Interior model) Sealing tape Purifier lock stationWater line Tapping screw x 12EA Clip A x 8EA INSTALLATION INSTRUCTIONS Tightening band Purifier (Exterior model) 27 INSTALLING OF THE WATER DISPENSER LINE For Interior Model (Case 1) Connecting to water supply line 1. Cold Water line -Shut off the main water supply line and turn the Ice 2. Pipe Clamp.maker to the off position. 3.Copper (or Plastic) line -Locate the nearest cold drinking water line. 4.Compression Nut -Follow the instructions in the ice maker installation kit. 5.Compression Sleeve 6.Shut Off Valve 7.Packing Nut. Connect the water line to the refrigerator -Slip the compression nut and plastic ferrule through the plastic tube. -After inserting the sleeve, tighten the compres-sion nut onto 1/4” compression fitting(union). Do not overtighten the compression nut. NOTE -Slip the compression ferrule and nut on copper(or plastic) tubing as shown. Tighten the comperssion nut onto the com-pression fitting(union). -Turn water on and check for any leakege. NOTE Waterline must be connected to drinkable water only (Case 2) Nut Check the water supply line Compression Ferrule Sleeve Compressionfitting Ferrule Compression Nut Connect the water pipe with coupler and tap. -Close the main water tap. -Connect coupler “A” to the tap. -Every join should be protected with sealing tape. WARRANTY INFORMATION This water line installation is not covered by the refriger-ator or ice maker manufacturer's warranty. Follow these instructions carefully to minimise the risk of expensive water damage. Note: If the coupler does not fit on the current tap, go the nearest authorised service dealer and purchase the right couplers fittings...

Dieses Handbuch ist für folgende Modelle:
Kühlen - 21KCMS (2.08 mb)
Kühlen - 21KCSW (2.08 mb)
Kühlen - 21KLDW (2.08 mb)
Kühlen - 21KLLB (2.08 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien