Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Americana Appliances Dateigröße: 466.45 kb Dateiname: Unterrichtssprache:

NOTE: Clearance “M” is between the rearmost part of the refrigerator and the wall behind the refrigerator. NOTE: Clearance “N” is the distance between the bottom of the lower side vent to the roof material. For ventilation height, see table VENTILATION HEIGHTS. See Figures 9 and 10. Side view View from above D H W D C BA Side view View from above D H W D C BA FIG. 11 Refrigerator Model Overall Dimensions Recess Dimensions Height A Width B Depth C Height H Width W Depth D RM2662 inch RM2663 mm 54-21/32 1388 24-7/8 632 26-1/32 661 53-3/4 1365 23-11/16 602 24 610 inch RM2862 mm 60-51/64 1544 24-7/8 632 26-1/32 661 59-15/16 1522 23-11/16 602 24 610 This method of installation and these clearances will give you adequate space for service and proper installation. OPERATING INSTRUCTIONS IMPORTANCE OF LEVELING A REFRIGERATOR In an absorption refrigerator system, ammonia is liquefied in the finned condenser coil at the top rear of the refrigerator. The liquid ammonia then flows into the evaporator (inside the freezer section) and is exposed to a circulating flow of hydrogen gas, which causes the ammonia to evaporate, creating a cold condition in the freezer. When starting this refrigerator for the very first time, the cooling cycle may require up to four hours of running time before the cooling unit is fully operational. The tubing in the evaporator section is specifically sloped to provide a continuous movement of liquid ammonia, flowing downward by gravity through this section. If the refrigerator is operated when it is not level and the vehicle is not moving, liquid ammonia will accumulate in sections of the evaporator tubing. This will slow the circulation of hydrogen and ammonia gas, or in severe cases, completely block it, resulting in a loss of cooling. Any time the vehicle is parked for several hours with the refrigerator operating, the vehicle should be leveled to prevent this loss of cooling. The vehicle needs to be leveled only so it is comfortable to live in (no noticeable sloping of floor or walls). When the vehicle is moving, the leveling is not critical, as the rolling and pitching movement of the vehicle will pass to either side of level, keeping the liquid ammonia from accumulating in the evaporator tubing. OPERATION Before starting the refrigerator, check that all the manual gas valves are in the ON position. DO NOT forget the manual shutoff valve on the rear of the refrigerator see FIG. 1. This refrigerator is equipped with a semi Automatic Energy Selector (AMES) control system, which can be set to automatically select either 120 volt AC or LP gas operation (AUTO mode), or if desired LP gas only (GAS mode). On 3-way model the control system can manually be set to DC operation (DC mode). The refrigerator controls will work down to 9.6 volt DC. ! WARNING Most LP gas appliances used in recreational vehicles are vented to the outside of the vehicle. When parked close to a gasoline pump, it is possible that the gasoline fumes could enter this type of appliance and ignite from the burner flame, CAUSING A FIRE OR AN EXPLOSION. FOR YOUR SAFETY, when refueling, shut off all LP gas appliances which are vented to the outside. 2-WAY display panel 3-WAY display panel DE ADE ON OFF AC DC GAS AUTO CHECK COLD 1 2 3 4 5 COLDESTON OFF AC GAS AUTO CHECK COLD 1 2 3 4 5 COLDEST 1 2 3 1 2 3 4 BC F START UP INSTRUCTIONS A. A continuous 12 volt DC supply must be available for the electronic control to function. B. Press the main power ON/OFF button (1) to the DOWN position. C. Press the TEMPERATURE SELECTOR button (3) 2-WAY Model or (4) 3-WAY Model until the lamp at the desired setting is illuminated. 2-WAY MODEL AUTO MODE 1. Press the AUTO/GAS mode selector button (2) to turn ON the Auto lamp (D). If 120 volts AC is available, the AC mode indicator lamp (B) will illuminate indicating AC operation. If 120 volts AC is not available, the GAS mode indicator lamp (C) will illuminate and the control system will automatically switch to GAS operation. 2. If the CHECK indicator lamp (E) illuminates and the GAS mode indicator lamp (C) is off, the controls have failed to ignite the burner in the GAS mode. GAS operation may be reset by pressing the main power ON/OFF button (1) to the OFF then ON position. (See step 2 under GAS MODE). 3. Press the TEMPERATURE SELECTOR button (3) until the lamp at the desired position is illuminated. GAS MODE 1. Press the AUTO/GAS mode selector button (2) to turn OFF the Auto lamp (D). The GAS mode indicator lamp (C) will illuminate. Within 45 seconds the burner should be ignited and operating normally. 2. On the initial refrigerator start-up it may take longer than 45 seconds to allow air to be purged from the gas line. If the gas does not ignite within 45 seconds the CHECK indicator lamp (E) will illuminate and the GAS mode indicator lamp (C) will go off. To reset when the CHECK indicator lamp (E) is illuminated, press the main power ON/OFF button (1) to the OFF and then ON position. NOTE: Do not c...

Herunterladen

Geben Sie zwei Ziffern: