Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: CDA
Dateigröße: 200.52 kb
Dateiname: a2c00adc-c6a1-4b87-8936-a53dff2ff8de.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
• The doors are closing properly. • The cooling system at the rear of the appliance is clean and free of dust, and not touching the rear wall. • There is enough ventilation at the side and rear walls. The appliance is noisy • The appliance is level and stable. • The side and rear walls are clear, and there is nothing resting on the appliance. • The cooling gas in the refrigerator will make a slight bubbling noise, even when the compressor is not running. There is water in the lower part of the refrigerator compartment • The drain hole in the channel at the back of the compartment is clear. Ice has formed on the back wall of the fridge • It is normal for some ice droplets to form on the back wall of the fridge. This does not constitute a fault with the appliance. • Ensure that no items inside the fridge are in contact with the back wall. If the temperature warning light flashes, contact CDA Customer Care. Installation And Ventilation This appliance must never be installed close to heat sources, e.g. heating elements, cookers or in damp places. • To ensure the appliance is level, you should use the height adjustable feet at the front of the appliance. • The cooling system at the rear of the appliance must not touch the rear wall. • The appliance must be installed with adequate ventilation. Ensure that there is clearance above the appliance to allow air to escape and that there is space between the rear of the appliance and the wall. The diagram shows the ventilation requirements for your appliance. Failure to provide adequate ventilation can lead to increased running costs and premature failure and may invalidate the warranty provided with the appliance. fig. 5 300 400 40 - 50 300 25 1778 814 45 25 57 837 545 540 = airflow Mounting the Fascia Door • Using a screwdriver, fix the mounting brackets to the appliance door, as shown in figure 6. • Position the appliance within the unit. Ensure that there is a gap of 3 to 4 mm between the non-hinged side and the cabinet wall. • Locate the slider in the bracket and fix the slider to the fascia door 20 to 22 mm from the edge of the fascia as shown in figure 7, ensuring that the slider is positioned centrally and horizontally within the bracket. Tighten securely by hand. • Fill the gap on the non-hinged side with the seal strip provided, as shown in figure 8. fig. 6 20 mm x4 x4 fig. 7 door gasket fig. 8 Reversing the door We recommend you seek the help of another individual to support the doors whilst performing this operation 1. Carefully prise off the cover cap for the top hinge and unscrew the screws fixing the top hinge to the appliance, you should support the upper door whilst doing this. 2. Carefully remove the upper door and place it somewhere safe. Note that there are spacers between the door and the hinge; note how many and their position. 3. Remove the central hinge by removing the 3 screws fixing it to the appliance; support the lower door whilst doing this. 4. Remove the lower door and place it somewhere safe, again noting the position of any spacer pieces. 5. Swap the bottom hinge to the opposite side. 6. Refit the lower door using any spacers and position the central hinge on the door. After removing the 3 cover caps, fix the hinge securely to the appliance. 7. The top hinge and replacement cover hinge covers are included in the fittings pack. Refit the upper door and the new top hinge and fix it securely to the appliance. 8. Fit the central cover caps and top hinge cover pieces in place to complete the process. Ensuring the door seals correctly: It is normal for the seal to be compressed after the door has been reversed. With the door closed, use a hair dryer to cause the seal to expand and fill the gap between the door and the body of the appliance. Take care not to use the hair dryer too close to the appliance, which could damage the seal. A distance of approximately 10 cm should be adequate. When completed, allow the seal and door to cool before touching them. Once done, the seal will remain in position. Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position. How to connect an alternative plug If the fitted plug is not suitable for your socket outlet, then it should be cut off and disposed of safely to avoid possible shock hazard. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used. As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: • The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or by...