Stimmen - 3, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
4. The appliance must be protected against rain, moisture and other atmospheric influences. 5. When positioning your appliance take care not to damage your flooring, pipes, wall coverings etc. Do not move the appliance by pulling by the door or handle. 6. Empty any water in the drain tray before moving. See section „Defrosting” and „Care & cleaning” for further information. 7. Make sure that the defrost water pipe at the back of the product is fixed to the plastic evaporating pan on the top of the compressor, to avoid defrost water spillage on the floor. Important! • Care must be taken while cleaning/carrying the appliance not to touch the bottom of the condenser metal wires at the back of the appliance, as this could cause injury to fingers and hands. • Do not attempt to sit or stand on top of your appliance as it is not designed for such use. You could injure yourself or damage the appliance. • Make sure that the mains cable is not caught under the appliance during and after moving, as this could damage the cable. • Do not allow children to play with the appliance or tamper with the controls. BEKO plc declines to accept any liability should the instructions not be followed. INSTALLATION INSTRUCTIONS 1. The space in the room where the appliance is installed must not be smaller than 10 cubic metres. 2. Do not put your fridge freezer in a cold room where the temperature is likely to go below +5 degrees C (41 degrees F) during night time and/or especially in winter. This fridge freezer has been designed to operate in ambient temperatures between +10 and +32 degrees C (50 and 90 degrees F) Therefore if the appliance is installed in an unheated/cold room (eg: conservatory/annex/ shed/garage etc) then the appliance will not operate causing the freezer compartment to run warmer and as a result the storage time of frozen food may be reduced. 3. Do not place the appliance near cookers, radiators or in direct sunlight as this will cause your appliance to work harder. If installed next to a source of heat or freezer, maintain the following minimum side clearances: From Cookers 2" (50 mm) From Radiators 12" (300 mm) From Refrigerators or Larder Fridge 1" (25 mm) 4 4. Make sure that sufficient room is provided around the appliance to ensure free air circulation. Fit the two plastic wall spacer supplied with the appliance rotating 1/4 turn to the condenser at the back of the refrigerator (see diagram). 5. The fridge/freezer should be located on a smooth surface. The two front feet can be adjusted as required. To ensure that, your appliance is standing upright adjust the two front feet by turning clockwise or anti-clockwise, until the product is in firm contact with the floor. Correct adjustment of feet avoids excessive vibration and noise. 6. Refer to cleaning and care section to prepare your appliance for use. WARNING! Do not connect your appliance to the electricity supply until all the packing and transit protectors have been removed including polystyrene block(s) inserted between the compressor motor and the cabinet (see diagrams). Do not remove the plastic drain tray fitted above the compressor motor on models with auto - defrost fridge. 5 GETTING TO KNOW YOUR COMBI BEKO FRIDGE / FREEZER 1 - Thermostat knob and interior light 2 - Interior light button 3 - Cabinet shelves 4 - Defrost water collection channel 5 - Salad crisper cover 6 - Salad crispers 7 - Ice Bank & ice cube tray 8 - Fast Freeze compartment 9 - Frozen froods storage drawer 10 - Adjustable feet 11 - Egg tray 11 - Door shelves 12 - Bottle shelf 6 REVERSING THE DOORS 7 Text Box: (You may need somebody to help you.) 1- Switch off the appliance at the socket outlet and pull out the mains plug. 2- Remove all loose items and fittings and food, if any, from inside the appliance and door racks. 3- Unscrew the bolts and remove the middle hinge while holding doors. (1) 4- Remove the fridge door from the top hinge. (2) 5- Remove the freezer door. (3) 6- Remove the plastic covers on the front top trim. (4) 7- Unscrew the bolts of the top hinge and remove top hinge. (5) 8- Reposition plugs on the opposite side. (6) 9- Carefully tilt the appliance on its back. (7) (You may need somebody to help you.) 10- Unscrew the screw level. (8) 11- Take off lower hinge. (9) 12- Remove the plastic cover and fit the tap which is in the plastic bag to the other side. (10) 13- Unscrew and remove the middle hinge bushing from fridge door. (11) 14- Screw and fix the new middle hinge bushing which is supplied in plastic bag to the other side. (12) 15- Reposition the hinge bushing and the tap on the freezer door. (13) 16- Unscrew and reposition the bottom hinge bushing. (14) 17- Take on lower hinge. (15) 18- Screw the screw level. (16) 19- Rotate the top hinge 180°. Unscrew the hinge pin and re-tighten it to the opposite side. (17) 20- Fit the top hinge and tighten the bolts. (18) 21- Fit the plastic cover on the front top trim. (19) 22- Locate the freezer door to the bottom hinge and...