Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Amana, modell SANTO C 7 18 40-4I

Hersteller: Amana
Dateigröße: 216.63 kb
Dateiname: 227499en.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Refrigerant The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable. • During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become damaged. • If the refrigerant circuit should become damaged: – avoid open flames and sources of ignition; – thoroughly ventilate the room in which the appliance is situated. Safety of children • Keep packaging material away from children. • Please make old appliances unusable prior to disposal. Pull out the mains plug, cut off the mains cable any locks or catches, to young children being trapped inside. • Do not allow children to tamper with the controls or play with the product. Place guide (A) on the inside part of the furniture door, in the upper and lower positions as shown in the figure and mark the position of external holes. Having drilled the holes, fix the guide with the screws supplied. Fix cover (C) on guide (A) until it clips into place. Open the appliance door and the furniture door at 90°. Insert the small square (B) into guide (A). Put together the appliance door and the furniture door and mark the holes as indicated in the figure. Remove the squares and drill holes with o 2 mm at 8 mm from the outer edge of the door. Place the small square on the guide again and fix it with the screws supplied. Open the door and push the appliance against the side of the kitchen unit opposite to that of appliance hinges. Fasten the appliance with 4 screws provided in the kit included with the appliance. Snap ventilation grille (C) and hinge cover (D) into position. Apply covers (B) into the relevant holes. Separate parts A, B, C, D as shown in the figure Daily Operation • Ice cream or ice cubes can cause “frost/freezer” burns if consumed straight from the freezer. • Do not operate any electrical appliances in the refrigerator/freezer (e.g. electric ice cream makers, mixers etc.). • Before cleaning the appliance, always switch off the appliance and disconnect from the electricity supply. • When unplugging always pull the plug from the mains socket, do not pull on the cable. Service • Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local AEG Service Force Centre. Disposal Appliance packaging information All materials are environmentally sound. The plastics can be recycled and are identified as follows: >PE< for polyethylene, e.g. the outer covering and the bags in the interior. >PS< for polystyrene foam, e.g. the pads, which are all free of chlorofluo rocarbon. The carton parts are made from recycled paper and should be disposed of at a waste-paper recycling collection location. . Disposal of old appliances For environmental reasons, refrigeration appliances must be disposed of properly. This applies to your old appliance, and - at the end of its service life - to your new appliance as well. Warning! Before disposing of old appliances make them inoperable. Remove plug from mains, sever the power cable, remove or destroy any snap or latch closures, to prevent small children being trapped inside. • Use an authorised disposal site. Contact your Local Council or Environmental Health Office to see if there are facilities in your area to recycle the appliance. Remove Transport Packaging The appliance and the interior fittings are protected for transport. • Remove all adhesive tape and packing pieces from the interior of the appliance. Shelf holders Your appliance is equipped with shelf retainers that make it possible to secure the shelves during transportation. To remove them proceed as follows: Raise the shelf from the back, push it in the direction of the arrow until it is freed and remove the retainers. Instructions for building-in Apply joint the sealing strip as shown in figure. Push appliance into the housing until stop strip (A) touches the kitchen unit. For a correct alignment make sure that the distance between the appliance and the cabinet is of 44 mm. 1. Unscrew the upper pin and remove Description of the Appliance the spacer 2. Remove the upper door A - Dairy compartment 3. Unscrew the middle hinge and the . B - Can storage shelves plugs and refit them on the opposite C Movable shelf side D - Bottle storage shelf 4. Refit the upper door, the upper pin and the spacer on the opposite side . E - Thermostat control F - Glass shelves 5. Unscrew the lower pin and remove the spacer and refit them on the G - Glass shelf opposite side. H - Salad drawers . I - Compartment for storing frozen food J - Compartment for freezing fresh food Housing dimensions Height 1780 mm Depth 550 mm Width 560 mm 22 7 Starting Up and Temperature Regulation Wash the inside of the appliance with lukewarm water with a little bicarbonate of soda added (5ml to 0,5 l...