Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
8 After-sales service Our after-sales service is there for you if your appliance needs to be repaired. We will always find the right solution in order to avoid unnecessary visits from a service technician. When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access). You can make a note of the numbers of your appliance and the telephone number of the after-sales service in the space below to save time should it be required. Please be aware that a visit by an after-sales engineer will be charged if a problem turns out to be the result of operator error, even during the warranty period. Please find the contact data of all countries in the enclosed customer service list. To book an engineer visit and product advice Rely on the professionalism of the manufacturer. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your appliances. Accessories for circulating-air mode (not included in the delivery) Notes ¦ Follow the installation instructions supplied with the accessories. ¦ For appliances with an additional internal filter, only the CleanAir recirculation module can be used. Basic equipment: Starter set for circulating-air mode - narrow Throw-away filter Basic equipment: Starter set for circulating-air mode - wide Throw-away filter Basic equipment: CleanAir recirculation module - narrow Throw-away filter Basic equipment: CleanAir recirculation module - wide Throw-away filter E no. FD no. After-sales serviceO GB 0844 8928999 Calls from a BT landline will be charged at up to 3 pence per minute. A call set-up fee of up to 6 pence may apply. IE 01450 2655 0.03 € per minute at peak. Off peak 0.0088 € per minute. 1 2 3 4 5 6 7 8 1 LZ53250 channel width 260 mm 2 LZ53251 channel width 260 mm 3 LZ53450 channel width 345 mm 4 LZ53451 channel width 345 mm 5 LZ57000 channel width 260 mm 6 LZ56200 channel width 260 mm 7 LZ57300 channel width 345 mm 8 LZ56200 channel width 345 mm INSTALLATION INSTRUCTIONS .............................................................................................................................. .... ¦This appliance is installed on the wall. ¦Follow the enclosed installation instructions for additional special accessories (e.g. for circulating-air mode). ¦The surfaces of the appliance are sensitive. Avoid damaging them during installation. .................................... : Important safety information Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners. The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location. The width of the extractor hood must correspond at least with the width of the hob. For the installation, observe the currently valid building regulations and the regulations of the local electricity and gas suppliers. When conveying the exhaust air, official and legal regulations (e.g. state building regulations) must be followed. Risk of death! Risk of poisoning from flue gases that are drawn back in. The exhaust air must not be conveyed into a functioning smoke or exhaust gas flue or into a shaft which is used to ventilate installation rooms that contain heating appliances. If the exhaust air is to be conveyed into a non-functioning smoke or exhaust gas flue, you must obtain the consent of the heating engineer responsible. Danger of death! Risk of poisoning from flue gases that are drawn back in. Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room air-dependent heat-producing appliance is being operated. Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coal- operated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney). In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked back into the living space. ¦ Adequate incoming air must therefore always be ensured. ¦ An incoming/exhaust air wall box alone will not ensure compliance with the limit. Safe operation is possible only when the partial vacuum in the place where the heat- producing appliance is installed does not exceed 4 Pa (0.04 mbar). This can be achieved when the air needed for combustion is able to enter...