.............................................................................................................................. Filters and drip trays .......................................................................................... and drip trays. ................................................................................................ on the cooktop from damaging the inside of the hood. For this reason, the metal filters must ALWAYS .................................................................... To Clean Filters and Drip Trays .................................................................................... cleaned once a month, or as needed. ..To clean the metal filters and drip trays, drain ...................................................................................... ...................................................................................... .......................................................................................... ........................................................................................ the metal. .................................................................................. .............................................................................................. They may also be cleaned in an automatic dishwasher. To Remove The Metal Grease Filters and the Drip Trays .. Turn the fan and lights off. ........................................................................................ ..........................Figure 1 ........................................................................................ ......................................Figure 2 .................................................................................................... out of the hood track. Figure 2. To Replace The Metal Grease Filters ........................................ To replace the Drip Trays Figure 2-3: 1. ..lace and seat the drip tray into the hood track. 2. Slide them left or right until all trays are side ............................................................ .................................................................................................. .............................................................. 5 Figure 3 Figure 2 Figure 1 operate be sure lights are inserted correctly before calling service. Note! Lamps are not supplied and must be purchased separately. Replace Lights Watt CLEANING THE HOOD A ys use the mildest cleaner that do the job. se clean, so loths, s s or paper t s. he . Wipe area dry to a oid ter mar . er c , place all parts in their proper positions be ore us . The cleaners recommended indicate a type and do not constitute an endorsement. se all products to directions. Care and Cleaning Chart A Anodized Aluminum T W r. T B Aluminum r them. C Plastic T and dry. Painted sur - DO NOT USE powdered cleansers or steel wool pads. A T 6 LIGHTS CAUTION: Should read before replace the lamps, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. Trouble Shooting Issue Cause What to do After installation, the unit doesn’t work? 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is not connecting properly. 2. Check the power connection when the unit is connected properly. 3. The switch board and control board wirings are disconnected. 3. Make sure the wirings between the switch board and control board are connected properly. 4. The switch board or control board is defective. 4. Call for Service Light works, but motor is not turning. 1. The thermally protected system detects if the motor is too hot to operate and shuts the motor down. 1. The motor will function properly after the thermally protected system cools down. The unit is vibrating. 1. The motor is not secure in place. 1. Tighten the motor in place. 2. Damaged blower wheel. 2. Call for Service 3. The hood is not secured in place. 3. Check the installation of the hood. The motor is working, but the lights are not. 1. Defective halogen lights. 2. The halogen lamps is loose. 1. Change the halogen lights. 2. Tighten the halogen lamps. The hood is not venting out properly. 1. The hood might be hanging too high from the cook top. 2. The wind from the opened windows or opened doors in the surrounding area are affecting the ventilation of the hood. 3. Blocking in the duct opening or ductwork. 4. The direction of duct opening is against the wind. 5. Using the wrong size of ducting. 1. Adjust the distance between the cook top and the bottom of the hood within 30” and 36” range. 2. Close all the windows and doors to eliminate the outside wind flow. 3. Remove all the blocking from the duct work or duct opening. 4. Adjust the duct opening direction. 5. Change the ducting to at least 8” or higher. Metal filter is vibrating. 1. Metal filter is loose. 1. Secure properly the grease fil...

Dieses Handbuch ist für folgende Modelle:
Dunstabzugshauben - HMWN36FS/01 (1.08 mb)
Dunstabzugshauben - HMWN48FS/01 (1.08 mb)