Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Light off There are no Plasmacluster ions being generated. • The light can be turned off by using the ‘Lights ON/OFF Button’ on the Remote Control. In this case, Plasmacluster ions are generated. (Please turn off the light if desired.) (See Page E-14) CLEAN-SIGN LIGHT The color changes according to the air condition. Clean (Green) Slightly Impure (Orange) Very Impure (Red) ABOUT THE CLEAN-SIGN • The condition of the CLEAN-SIGN depends on the room air condition detected by the Odor Sensors when the plug is inserted into the wall outlet. • It is possible to have a green CLEAN-SIGN with impurities in the air at the time that the air purifier was just introduced to the room environment. After a while, however, the base impurity rate will be adjusted to detect room air condition correctly. • Use the Lights ON/OFF Button on the remote control to turn off the Indicator lights if desired. CLEAN FILTER INDICATOR LIGHT Clean the Active Carbon Filter when the CLEAN FILTER Indicator Light activates. (The indicator light will activate in about 2 months, when using the unit 24 hours daily.) (See Page E-16) E-13 1 hour Cancel 4 hours 8 hours ION AUTO When pressed, the unit will switch between Clean Mode and the Ion Control Mode automatically depending on the amount of impurities in the air as detected by the dust and odor sensors. Clean Mode will operate for 1 minute when the Auto function is selected. ION CONTROL When pressed, the unit will constantly operate in Ion Control Mode. The Plasmacluster Ion Indicator Light is green. CLEAN When pressed, the unit will constantly operate in the Clean Mode, in which the same numbers of positive and negative ions are discharged. The Plasmacluster Indicator Light is blue. ION OFF The generation of ions will cease and the Plasmacluster Indicator Light will go out. REMOTE CONTROL OPERATION OPERATION Operations available withthe Remote Control • AUTO • MANUAL • POLLEN • OFF TIMER • QUICK CLEAN • Lights ON/OFF Plasmacluster Ion mode selections • ION AUTO • CLEAN • ION CONTROL • ION OFF POWER ON/OFF Button • When you press the POWER ON/OFF Button, a short beep will sound and operation will start in AUTO Mode. • Unless the power cord has been unplugged, the operation starts in the previous mode the unit was operated in. • To stop, press the POWER ON/OFF Button again. A long beep will sound and operation will stop. Auto (Fan Speed) Button The fan speed switches automatically depending on the amount of impurities in the air. Manual (Fan Speed) Button The fan speed can be switched among Silent, MEDIUM and MAX settings. QUICK CLEAN Button See page E-12 LIGHTS ON/OFF Button Switches the Plasmacluster Indicator Light and CLEANSIGN Light either ON or OFF. Pollen Mode Operation Button See Page E-12 Filter Reset Button When the Washable Active Carbon Filter is cleaned and reinserted into the main unit, press the Filter Reset Button with a pointed instrument such as a pen. The Filter Indicator light will then go out with a beep. Transmitter Plasmacluster Ion Mode Selections Off Timer Button The set time switches every time the button is pressed as shown below. • The indicator light shows the remaining time. • The unit will stop operation when the time is up. 1 hour Cancel 4 hours 8 hours ION AUTO When pressed, the unit will switch between Clean Mode and the Ion Control Mode automatically depending on the amount of impurities in the air as detected by the dust and odor sensors. Clean Mode will operate for 1 minute when the Auto function is selected. ION CONTROL When pressed, the unit will constantly operate in Ion Control Mode. The Plasmacluster Ion Indicator Light is green. CLEAN When pressed, the unit will constantly operate in the Clean Mode, in which the same numbers of positive and negative ions are discharged. The Plasmacluster Indicator Light is blue. ION OFF The generation of ions will cease and the Plasmacluster Indicator Light will go out. REMOTE CONTROL OPERATION OPERATION Operations available withthe Remote Control • AUTO • MANUAL • POLLEN • OFF TIMER • QUICK CLEAN • Lights ON/OFF Plasmacluster Ion mode selections • ION AUTO • CLEAN • ION CONTROL • ION OFF POWER ON/OFF Button • When you press the POWER ON/OFF Button, a short beep will sound and operation will start in AUTO Mode. • Unless the power cord has been unplugged, the operation starts in the previous mode the unit was operated in. • To stop, press the POWER ON/OFF Button again. A long beep will sound and operation will stop. Auto (Fan Speed) Button The fan speed switches automatically depending on the amount of impurities in the air. Manual (Fan Speed) Button The fan speed can be switched among Silent, MEDIUM and MAX settings. QUICK CLEAN Button See page E-12 LIGHTS ON/OFF Button Switches the Plasmacluster Indicator Light and CLEANSIGN Light either ON or OFF. Pollen Mode Operation Button See Page E-12 Filter Reset Button When the Washable Active Carbon Filter is cleaned and reinserted into the main unit, press the Filter Reset Bu...