Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
• Use only a 120 volt outlet. • The air purifier has a polarized plug (one blade is wider than the other is). This plug will fit in a polarized outlet only one way. Initially, if the plug does not fit into the outlet, reverse it. If it still does not fit, contact a qualified electrician or service person. • Do not use the air purifier if the power cord or plug is damaged or the connection to the wall outlet is loose. • Periodically remove dust from the power plug. • Do not insert fingers or foreign objects into the intake or air outlet. • When removing the power plug, always hold the plug and never pull the cord. Electrical shock and/or fire from short circuit may occur as a result. • Do not remove the power plug when your hands are wet. • Do not use this air purifier near gas appliances or fireplaces. • Remove the power plug from the wall outlet before cleaning the unit and when not using the unit. Electrical shock from bad insulation and/or fire from short circuit may occur as a result. • If the power cord is damaged, it must be replaced by the manufacturer, its service agent, Sharp authorized Service Center or similarly qualified person in order to avoid a hazard. • Do not operate when using aerosol insecticides or in rooms where there is oily residue, incense, sparks from lit cigarettes, chemical fumes in the air or under a humid condition. • Be cautions when cleaning the air purifier. Strong corrosive cleansers may damage the exterior. • Only Sharp Authorized Service Centre should service this air purifier. Contact the nearest Service Centre for any problems, adjustments, or repairs. • The batteries must be removed from the remote control before disposal, and the batteries must be disposed of safely. NOTE - Radio or TV Interference If this air purifier should cause interference to radio or television reception, try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the air purifier and radio/TV receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This product fulfils the requirement of the International standard CISPR 11. In conformity with this standard, this product is classified as group 2 class B equipment. Group 2 means that the equipment intentionally generates radio-frequency in the form of electromagnetic radiation for electro-discharge machining equipment. Class B equipment means that the equipment suitable to be used in domestic establishments. E-6 CAUTIONS CONCERNING OPERATION • Do not block the intake and air outlet. • Do not use the unit near or on hot objects, such as stoves or heaters or where it may come into contact with steam. • Do not lay the unit down when using. • Always hold the handle on the back of the main unit when moving it. Holding the front panel when carrying may cause it to detach, thus dropping the unit and resulting in bodily injury. • Do not operate the unit without the filter. • Do not wash and reuse HEPA filter. Not only does it not improve filter performance, it may cause electric shock or malfunction. • Clean the exterior with a soft cloth only. The unit surface may be damaged or cracked. In addition, the sensor may malfunction as a result. REMOTE CONTROL LIMITATIONS DO NOT USE THE REMOTE CONTROL IN THE FOLLOWING LOCATIONS: • Any location where there is inverter lighting equipment or electronic spontaneous lighting equipment The remote control may become inoperative. In this case, move away from such lighting equipment or change direction. • Location exposed to direct sunlight or fluorescent. The unit may not receive signals from the remote control. INSTALLATION GUIDELINES • During the operation of the product, please place the unit at least 7feet(2m) away from equipment which involve electric wave such as televisions, radios or wave clocks, in case electrical interference occurs to such equipment. • Avoid a location where the sensor is exposed to direct wind. The unit may not operate properly. • Avoid locations where curtains, etc., come into contact with the intake or air outlet. Curtains, etc., may become dirty or a malfunction may occur. • Avoid locations where the unit is exposed to condensation, due to drastic temperature changes. (Use under appropriate conditions between 0 and 35°C in the room.) • Place on a stable surface with sufficient air circulation. When placing the unit on a heavily carpeted area, it may cause the unit to vibrate slightly. • Do not install when there is generation of lampblack, such as in a kitchen, etc. The unit surface may crack or the sensor may malfunction as a result. • Leave about 2feet(60cm) of space from the wall. The wall behind the air outlet may become dirty as time passes. When using the unit for extended period of time in the same location, use a vinyl sheet, etc., to prevent the wall from bec...