Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Kenmore Dateigröße: 637.56 kb Dateiname: Unterrichtssprache:

3 OPERATION WARNING: To reduce the risk of electrical shock, this equipment is supplied with a 3-prong power cord with a grounding lug on the plug. It is intended to be used with a standard 3-prong 120 volt AC outlet. If the plug does not fit your outlet, contact qualified personnel to install the proper receptacle. DO NOT alter the plug in any way. The operation of the unit is very simple.Turn it on by setting the green control switch to high (3), med (2) or low (1). When the Clean Air Light (green) is on, this is an indication that the Forever Filter" is working properly. The light will NOT be on when the switch is in the "Quick Dry" position. The "Quick Dry" position is provided for drying the filter after cleaning. OPERATION NOTES !. The speed shoul dbeset on high (3)for two minutes , before switching to the desired speed to initially start the unit. Control Panel Diagram i _,j I,, ,,, ,,,,, . Your Sears Kenmore Air Cleaner_is equipped with a Negative ton Generator (Ionizer). The negative ions are discharged through needles located just beneath the air discharge grill. if you place your hand close to the negative ion field generated by the needles (within 6-!2 inches of the grill) for a period of time, and then touch a grounded (metal) object, you may experience a mild static discharge similar to the static electricity charge from "carpet shock". The static discharge is simply a result of the negative ions that have built up on your hand being discharged to ground. • Please note that there is no cause for alarm should this occur. Your air cleaner is nottdefective. CLEANING AND CARE In addition to the exterior of the unit, there are three areas that require periodic cleaning: the pre-filter, the Forever FilterTM, and the Negative Ion Generator Needles. ACCESS TO FILTERS Before performing any maintenance, turn the unit to the OFF position and unplug the power cord. To access the filters for cleaning, simply place your hands on each side of the front access panel and pull towards you. CLEANING THE FOREVER FILTER TM Please use care when handling the Forever Filter" to ensure you do not damage the ionizing wires or metal plates. 1. Remove access panel as described above. 2. Pivot tension ciips 90 degrees (horizontal orientation) to release the Forever Filters". 3. Pull on the plastic handles at the base of the Forever Filter". 4. After removing the Forever FilterTM, the Pre-Filter'can be easily slid out of its track (please see instructions for cleaning the Pre-Filter). TENSION CLIPS HANDLES The twin Forever Filters TM shoUld be cleaned every one to three months depending on the conditions in your particular environment. Failure to clean the Forever Filter periodically will degrade performance of the air cleaner. The filter can be washed with Zap-lt cleaner sold through Sears (Sears stock # 8395) or with a dishwashing detergent such as Electrasol. If using Zap-lt, spray the filter with water and then spray the metal plates with Zap-lt. Allow to soak for 5-t0 minutes before rinsing with water. Or If using dishwashing detergent, completely immerse the Forever Filter TM in hot soapy water for 20 to 30 minutes. Rinse it off, using a sprayer if available. Shake as much water from the filter as possible After the first cleaning, the metal surface of the electronic filtermay not beas shiny as before, This is normal and does not reduce effectiveness. CLEANING THE PRE_FILTER 1. Remove the filter from its rack. 2. Simply rinse the pre-fiIter in warm soapy water. 3. Shake off the excess water. 4. Return to its rack on the air intake of the Forever REINSTALLING FOREVER FILTERS" 1. Ensure the Pre-filter is placed inthe tracks provided on the bottom side of the Forever Filter TM (same side as plastic handles). 2. Return the Forever Filters TM to their original position in the air cleaner. 3. Pivot the tension clips back to their original position _ (vertical orientation) to ensure the Forever Filter TM is properly located. 4. Replace the front access panel by inserting the top first and then push the lower outside corners toward the rear of the cabinet until it snaps into place. 5. After reinstalling the cleaned filters in the unit, operate the unit...

Herunterladen

Geben Sie zwei Ziffern: