Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Hunter Fan, modell 30212

Hersteller: Hunter Fan
Dateigröße: 1.89 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

6. DO NOT tilt or move the Air Purifier while it is in operation. Shut off and unplug before moving. 7. DO NOT immerse the Air Purifier in water as permanent damage will occur. Refer to and follow the CLEANING AND FILTER REPLACEMENT instructions. Introduction Thank you for purchasing the HEPAtech® Air Purification System from Hunter Fan Company. You have purchased our latest development in portable Air Purification Systems. This system has been developed to improve the quality of the air you breathe. Our HEPAtech® Air Purification System out performs other air purification systems by quickly and effectively removing dust, smoke, and pollen particles as small as .1 microns in size. Room air is pulled in through the front grill and cleaned across the HEPAtech® filter. Clean air is then released out the top grill in order to avoid stirring up settled particles. Using the Ionizer Using the ionizer improves the quality of air in the room. Negative ions are released into the air and positively charged dust, smoke, and pollen particles are attracted to the negative ions. These particles settle out of the air and can be vacuumed up during normal cleaning. These particles are also more easily captured by the HEPAtech® filter as they pass through the HEPAtech® Air Purification System. To ensure the best air circulation in the room, we recommend that you place your air purifier six inches away from any walls. 41769-01 04/26/2005 ©2005 Hunter Fan Company 41769_rev 04-26-05_B.indd 2 4/26/05, 1:49:23 PM ® 3 ENGLISH ©2005 Hunter Fan Company 41769-01 04/26/2005 Setting Up Your Air Purifi er 1. Remove your air purifi er from the box and take it out of the clear plastic protective bag. 2. Place your HEPAtech® Air Purifi er on a fi rm, fl at fl oor. 3. Before turning the Air Purifi er ‘on,’ open the front grill. • For Models 30078 & 30079: To release the front grill, press the buttons on the side until the front grill slides easily over the buttons. (Refer to Figure 1.) • For Models 30212 & 30213: To release the front grill, place your fi ngers behind the tabs and pull forward. (Refer to Figure 2.) 4. Next, check the HEPAtech® fi lter by pressing fi rmly on all four corners of the fi lter to ensure that it is fully inserted into the fi lter opening. 5. The carbon pre-fi lter is mounted inside of the front grill with “hook” tape. Confi rm that it covers the grill vents. (Refer to Figure 3.) 6. Place the fi lter installation reminder sticker on the inside edge of the front grill. Circle the month and write the year of installation for the pre-fi lter and HEPAtech® fi lter. 7. Replace the fi lter and front grill. Be sure that the bottom grill tabs are in position fi rst, and then push the top of the grill forward until it is closed. The unit is now ready for normal operation. NOTE: This unit will not operate unless the door is placed in the correct position. 8. Plug the unit into a 120V electrical outlet. AIR PURIFIER PARTS 01 2 3 .... .... .... .... .... .... .... .... .... .... .... .... .... .... .. 012 3 Figure 1 - Models 30078 & 30079 HEPAtech® Filter Pre-Filter Front Grill Buttons for opening the front grill Tabs for opening the front grill HEPAtech® Filter Pre-Filter Front Grill Figure 2 - Models 30212 & 30213 Figure 3 Hook Tape Grill Vents Hook Tape 41769_rev 04-26-05_B.indd 3 4/26/05, 1:49:23 PM 4 ® Operating Your Air Purifier On/Speed Control: Rotate the Speed Control knob to set the desired speed. A setting of zero (0) indicates that the unit is off, one (1) is low speed, two (2) is medium speed, and three (3) is high speed. The fan speed can be adjusted at any time. Ionizer: Press this button to turn ‘on’ the ionizer. When the ionizer is ‘on’, the green light near the button will be illuminated. Pre-Filter and Filter Timers This air purifier contains timers that indicate when the pre-filter and filter should be changed. The timer automatically counts the number of hours that each filter has been in use. When the pre-filter counter reaches 1400 hours (approximately three months of use), the pre-filter indicator will be lit to show that the pre-filter should be changed. When the HEPAtech® filter counter reaches 2800 hours (approximately four to six months of use), the HEPAtech® filter indicator will be lit to indicate that the filter should be changed. The exact life of the pre-filter and filter will depend upon the environment. If necessary, the filters should be changed more frequently. The reset the pre-filter or filter timers when one indicator (or both) is lit: 1. Change the fi lter and/or pre-fi lter as described in the Maintenance section of the manual. 2. To reset ...