Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung GE, modell GE SmartWater GXWH20F

Hersteller: GE
Dateigröße: 654.94 kb
Dateiname: bda293a2-1300-42af-a472-e1618652e808.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Assemble a fitting through the mounting bracket hole to 4 the inlet and outlet of the head. Start each fitting by hand to make sure they don’t cross thread. Use a 11.8. wrench to tighten fittings firmly. DO NOT OVERTIGHTEN. GXWH04F GXWH20F 3 STEP-BY-STEP INSTALLATION INSTRUCTIONS (cont.) Attach Fittings to Water Line D 21 Slip a compression nut onto each pipe. Next, slip the brass ferrule onto each pipe. Brass ferrule Brass ferrule Hex nut Hex nut Installing the Unit 1 Align filter assembly with pipe ends, making certain that the incoming water supply is going into the filter opening marked 43 Hang mounting bracket with unit onto previously installed screws. Drive two screws to secure unit tightly to the wall if “IN”. It may be necessary to spread the pipe ends apart to necessary. install filter assembly. Install a filter into the housing and tighten canister to seal (see Filter Cartridge Replacement section). Using a 11.8. wrench to hold the fitting in place, use a 11.4. 2 wrench to tighten the nut. Repeat process for other fittings. Installing the Ground Wire NOTE: If your house plumbing is plastic, it would not be used as a grounding path, and this step should be skipped. 1 Clean copper pipe and ends of wire with emery paper. Bare wire is recommended. If insulated wire is used, it should be stripped 3/4. at each end before cleaning with emery paper. IMPORTANT: A copper or galvanized cold water pipe is often used 32 Attach bronze clamps to copper pipe. Tighten screws. to ground electrical outlets in the home. Grounding protects you from electrical shock. The water filter housing may have broken Attach wire to clamps as shown. Tighten screws. this ground path. To restore connection, install a 12. long, 6-gauge copper wire across the filter, and tightly clamp using Ground wire UL-approved 1/2.–1. bronze grounding clamps at both ends as shown. Zinc clamps should not be used on copper plumbing. For GXWH04F, wire and clamps may be purchased separately from your local hardware store, or are available by visiting our Clamp Website at ge.com, or from Parts and Accessories by calling 800.626.2002 (U.S.)or 800.663.6060 (Canada)—order part number WHKIT. Final Check 1 Install filter, if not already done. (See Filter Cartridge Replacement section.) 54 If leaking from fittings, shut off water pressure and tighten or reseal fittings. If leaking from the canister, tighten the canister with a wrench. Open any downstream faucet and allow filter and housing to flush for 5 minutes. 32 Slowly turn on water supply. Check entire system for leaks. Timer Installation and Application Instructions Timer battery installation and change Blue reset button Insert coin or screwdriver into the slot between timer cap and base. Gently pry them open and Timer cap separate timer base from cap. Install or change 2 AAA 2 new AAA 1.5 volt batteries. After you have batteries the batteries in place, line up the base and cap Timer base and snap them back together. Timer seat It is recommended to change the batteries at least every 2 filter changes, or when the blue Head LED light seems dim. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (ni-cad, ni-mh, etc.) batteries. Installation of timer Hold the timer body in the center and gently push the timer to its seat at the top of the head or attach it in a remote location for easy viewing. Timer reset and application After new batteries are installed or filter is changed, push and hold the blue timer reset button (hold the reset button for approximately 5 seconds). Release the reset button after the light stops flashing. The timer has been reset. The light will flash again in 90 days to remind you that it is time to change the filter. 4 PARTS LIST G G X X W W H H 0 2 4 0 Ref. No. Part No. Part Description F F 001 WS35X10023 Installation Kit — 1 or WHKIT 002 WHTIMER Timer 1 1 003 WS03X10038 O-Ring 1 1 005 WX5X140 Canister Wrench 1 1 006 FXUSC (Rev. 2) Filter Element—Polypropylene Fiber — 1 FXWPC Filter Element—Pleated — — FXWSC Filter Element—String — — FXWTC (Rev. 2) Filter Element—Carbon Paper — — 999 49-50202-1 Installation Instructions 1 1 999 006 003 003 001 001 002 005 To obtain replacement parts, call toll-free 800.626.2002 (U.S.), 800.663.6060 (Canada—English), 800.361.3869 (Canada—French). 002 LIMITED ONE YEAR WARRANTY • What does this warranty cover? — Any defect in materials or workmanship in the manufactured product. • What does this warranty not cover? — Filter Cartridges. — Service trips to your home to teach you how to use the product. — Improper installation, delivery or maintenance. — Failure of the product if it is abused, misused, altered, used commercially or used for other than the intended purpose. — Use of this product where water is microbiologically unsafe or of unknown quality, without adequate disinfection before or after the housing*. Housings certified for cyst reduction may be used on disinfected water that may contain filterab...