Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your water softener. ▲ Your water softener will remove hardness minerals and “clear water” iron from water, up to the limits shown on page 21. It will not remove other types of iron, acids, tastes and odors, etc. It will not purify polluted water or make it safe to drink. ▲ Protect the softener and piping from freezing. Damage from freezing voids the softener warranty. See page 16. _ CAUTIONS _ PLEASE READ AND COMPLY WITH THE FOLLOWING GUIDES TO PREVENT DAMAGE TO THE SOFTENER OR OTHER PROPERTY, PERSONAL INJURY, OR POSSIBLE FATAL SHOCK. ▲ THIS SOFTENER WORKS ON 24 VOLTS ONLY. BE SURE TO USE THE TRANSFORMER INCLUDED, AND PLUG IT INTO A 120V OUTLET. ▲ Unplug the transformer right away if the power cable should become damaged or frayed. Make repairs before plugging back into the power outlet. ▲ Always unplug the softener from electrical power before removing outer valve covers. 4 SECTION 1 WATER SOFTENER START-UP ] 1B. CHECK LIST OF ALL STEP-BY-STEP GUIDES TO INSTALL Refer to the Installation Manual, part no. 7141417, for step-by-step guides. To be sure you have done all the steps to install the softener, read the following list. Page numbers referred to are in the Installation Manual. J Is the house water flow going INTO the softener valve INLET? Trace piping to be sure. See pages 10 and 11. J Is the plumbing bypass valve (or 3 valves) set for SERVICE? See page 18. f Is the valve drain hose connected the right way, and without sharp bends or kinks that could stop or reduce water flow? See page 16. f Is the softener power cable connected to the transformer, and is the transformer plugged into an inside, 120V-60Hz electrical outlet? See page 20. f Be sure to restart the water heater. See page 20. Bypass mi J Valves N plastic Water Heater 5 SECTION 1 WATER SOFTENER START-UP -1 1C. PROGRAM THE TIMER FIG. 1 1. SET THE TIMER When the transformer is plugged into the electrical outlet, 12:00 AM, SUnday began to flash in the time display. Set the time of day and present day of week as follows: a. SET TIME OF DAY 1. Press the PRESENT TIME AND DAY button m once. The hour display continues to flash. 2. Press the SET/CLEAR button 0 until the present hour of the day shows in the display. Be sure AM for morning hours, or PM for afternoon and evening hours shows. NOTE: Press SET/CLEAR and quickly release to move the hour display ahead 1 at a time to the correct hour. Or, hold the SET/CLEAR button to move the display ahead 2 hours each second, to the correct hour. 3. Press button m once to steady the hour display, and minutes begin to flash. Repeat step a2 to set the correct minutes. 4. Press button m again to steady the minute display (day will begin flashing). Figure 2 shows the timer set at 3:30 PM. See step b to set the present day. b. SET PRESENT DAY OF WEEK 1. Press the SET/CLEAR button 0 to set the present day of the week in the display. NOTE: Press SET/CLEAR and quickly release to move the day display 1 at a time. Or, hold the SET/CLEAR button to move the day display ahead 2 days each second. 2. Press the PRESENT TIME AND DAY button m again to steady the entire display. Figure 2 shows the timer set at TUesday. FIG. 2 PM ~i in O DU tu_ EXAMPLE: This drawing shows 3:30 PM as the present time of day, and TUesday is the current day of the week. □ urn □ Q ra PRESENT TIME AND DAY RECHARGE TIME RECHARGE DAY SET / CLEAR ON / OFF VACATION HOLD RECHARGE NOW No other settings are needed after installing your water softener. The softener is factory set to regenerate every Monday, Wednesday and Saturday (beginning at 2:00 AM). For most families, this gives enough soft water for their needs. However, if you want the softener to regenerate at a different time, or on different days, or to set for the most efficiency, see “Fine-Tuning Your Water Softener,” page 18. SEE PAGE 9 FOR OTHER TIMER CONTROLS AND FEATURES. 6 SECTION 1 WATER SOFTENER START-UP 1D. SANITIZING THE WATER SOFTENER Care is taken at the factory to keep your water softener clean and sanitary. Materials used to make the softener will not infect or contaminate your water supply, and will not cause bacteria to form or grow. However, during shipping, storage, installing and operating, bacteria could get into the softener. For this reason, sanitizing as follows is suggested® when installing. 1. Lift the salt hole cover and use a pail or hose to fill the salt storage tank with at least 3 gallons of water. 2. Remove the brinewell cover (FIG. 3) and pour about 3/4 ounce of common 5.25% household bleach (Clorox, Linco, BoPeep, White Sail, Eagle, etc.) in the softener brinewell. 3. Press the ON/OFF-HOLD button and hold for 3 seconds to start a recharge. This first recharge does several things. — It draws the bleach into an...
Dieses Handbuch ist für folgende Modelle:Wasserfilter - 625.3483500 (444.61 kb)