Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Bunn
Dateigröße: 2.29 mb
Dateiname: 39338.0000.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
This will take approximately 7 minutes. 6. The water will heat to the factory default setting of 200° F (93° C) for most dispensers, and 90° F (32° C) for other dispensers. 7. Refer to PROGRAMMING to set the tank temperature, ready temperature, and dispense volumes. DRAINING THE DISPENSER CAUTION - The dispenser must be disconnected from the power source throughout these steps. 1. Disconnect the dispenser from the power source. 2. Shut-off and disconnect the incoming water supply 3. Remove the 4-40 screws at the sides of the top panel. 4. Gently remove one of the grommets from the tank lid. 5. Insert a syphon tube to the bottom of the tank and syphon ALL of the water out. CLEANING The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. WALL MOUNTED INSTALLATION If the dispenser is wall mounted, the bottom of the dispenser should be at the same height as a counter or table top. Use B.O.M. part #12542.0000 for side mounted Wall Bracket Kit or # 13125.0001 for front mounted Wall Bracket Kit . SUPPORT FOR LARGE RECEPTACLES CAUTION: If the dispenser is to be used with larger receptacles such as pitchers or pots, those receptacles must be adequately supported during dispensing of hot water to avoid spillage of very hot water. This support may be provided by a table or counter top, or use B.O.M. part #12599.0000 Shelf Kit. 39338 012609 OPERATING CONTROLS d. c. a. b. P3743 e. (a) VOLUME SELECTOR BUTTONS Press and release the button corresponding to the Small, Medium, or Large volume, to select the desired amount of water to be dispensed. Pressing a different button after a cycle has been initiated does not change the volume in progress. (b) AUTO STOP/MANUAL DISPENSE BUTTON Press and release button to stop a dispense cycle. Press and hold button to dispense manually. (c) HIDDEN PROGRAMMING BUTTON (d) LED INDICATORS (e) DISPENSE NOZZLE 39338 100606 PROGRAMMING When power is applied to the dispenser, the display located on the bottom of the main circuit board will show the revision level of the software for 5 seconds, and then go to (-). While the tank is filling, the display will read (FIL). When the tank is full the display will return to (-). LEVEL 1 PROGRAMMING TANK WATER TEMPERATURE & READY TEMPERATURE SET-UP 1. Press and hold the center button until P1 appears on the display (approximately 3 seconds) then release button. The tank water temperature set point will appear on the display. Factory default is 200° F for most dispensers, and 90° F for some. 2. Press the (+) button to increase the temperature set point, and the (-) button to decrease the set point. 3. After the Tank Temperature is entered, press and release the center button once more. The display will read P2, then show the ready temperature set point. Factory default is 195° F for most dispensers, and 85° F for some. 4. Use the (+) button to increase the temperature set point, and the (-) button to decrease the set point. 5. To exit Level 1 Program press and release the center button once more. The display will show Software version, then (-). LEVEL 2 PROGRAMMING DISPENSE TEMPERATURE LOCKOUT, FAHRENHEIT OR CENTIGRADE SELECTION, & FACTORY DEFAULTS 1. To enter Level 2 Programming, press and hold the center button until H1 appears on the display (approximately 6 seconds) then release button. The display will either read noL (LOCKOUT DISABLED) or Loc (LOCKOUT ENABLED). When (ENABLED), unit will not dispense if the Tank Temperature is below the (READY) temperature setting. 2. Use the (+) or (-) buttons to alternate between Loc and noL. P3747 CENTER BUTTON RIGHT BUTTON LEFT BUTTON 39338 012609 3. Press and release the center button once more. The display will read H2, then show either FAH (Degrees in Fahrenheit) or Cen (Degrees in Centigrade). 4. Press and release the (+) or (-) buttons to alternate between FAH and CEn. 5. To Exit Level 2 Programming, press and release the Center Button twice more. The Display will show the Software Version, then (-). RESTORING FACTORY DEFAULTS 1. To restore Factory Defaults (This clears all settings that were previously entered), press and release the center button until H1 appears on the display (approximately 6 seconds). Release the Center Button, then press and release the Center Button twice more. The display will read H3, then show (- - -). 2. Press and hold both (+) and (-) buttons to initiate the resetting of the factory default settings. The display (- - -) will flash on and off during this time (about 5 to 7 seconds). 3. When the factory default numbers are loaded in, the display will stop flashing, then read don (DONE). You can now release the two buttons. NOTE: If you release the two buttons at any time before the display reads don, the Factory Default numbers will not be entered. The old numbers will remain in the memory. 4. To exit Level 2 Program press and release the center button once more. The Display will show the Softw...