Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
THESE INSTRUCTIONS MUST BE POSTED NEAR THE BOILER AND MAINTAINED IN LEGIBLE CONDITION FOR REFERENCE BY THE OWNER OR SERVICE PERSON. Boiler Serial No. OWNER: For service and repairs to the heating system, please contact your Heating Contractor. The following information should be filled in by your Heating Contractor, and used by you when seeking information concerning the boiler. Model No. Heating Contractor: Address: Telephone Number: Rev. B 9/15/10 QHTih BIASI The New Style of Warmth Dear Customer, Thank you for buying a BIASI 3Wood Boiler. The 3Wood Boiler system is a cast iron, solid fuel, hot water boiler, using the famous Biasi (3-pass) design. This Boiler is rugged and engineered for maximum heating efficiency. We realize that it is not possible to answer all the questions about the 3Wood Boiler System in this manual. Reading this installation Manual does not make the reader an expert in all aspects of installation and operation, and does not replace the need for a qualified, licensed heating contractor. We urge you to contact your installing contractor or distributor if you are in question about any aspect of your boilers performance. Our main concern is that you are satisfied with your boiler and its performance. All BIASI boiler blocks are built in accordance with ASME boiler pressure vessel code, and bear the “H” stamp. The entire range of 3Wood Boilers have been tested to ETL standards. The BIASI 3Wood boiler block has a limited lifetime warranty (refer to back of manual). Thank you for purchasing our 3Wood series boiler. If you have any questions or comments call please don’t hesitate to contact us immediately . Our goal is 100% customer satisfaction. Sincerely, QHT Inc. 2 QHTibBIASI The New Style of Warmth Table of Contents Important Information 4 Warnings and safety rules, Identification 5-6 Procedure in event of power failure 7 Refueling the Boiler 8 Wood Burning 9 Heat value of wood, Wood Storage, Ash Removal 10 Creosote, Runaway Fire 11 Chimneys 12 Coal Firing 13 3Wood Design 14 Installation Considerations 15 Layout of Main Components 16 Transporting and Minimum Clearances 17 Flue Gas Outlet and Combustion Air 18 Assembling the Casing 19 Installation of Controls 20 Installations of Flue Gas Partition and Draft Regulator 21,22 Commissioning the Boiler 23 3WOOD as only boiler piping and wiring 24,25 4 Way Mixing Valve Piping and Wiring 26,27,28 Parallel Piping and Wiring 29,30,31 Boiler and Casing Parts 32,33,34 Useful References 35 Shutdown 36 Troubleshooting 37 System Checkout 38 Warranty 39 3 QHTih BIASI The New Style of Warmth IMPORTANT INFORMATION Please read this page carefully. ALL BOILERS MUST BE INSTALLED IN ACCORDANCE WITH NATIONAL, STATE AND LOCAL PLUMBING, HEATING AND ELECTRICAL CODES AND ORDINANCES, AS WELL AS THE REGULATIONS OF THE SERVING ELECTRICAL, WATER AND GAS UTILITIES. All systems should be designed and installed by licensed heating contractors who are knowledgeable in the layout and installation of multi-fuel heating systems. WARNING • The 3WOOD Boiler must be positioned to provide at least 36” of clearance between any combustible material and the sides, rear, and top of the boiler. At least 60” must be provided between the front of the boiler and any combustible material. Boiler must be set on a non-combustible floor. • Do not burn volatile garbage, gasoline, naphtha, propane, engine oil, or other flammable liquids. All flammable liquids (especially gasoline), debris, rags, paper, wood scraps, etc., should be kept clear of the boiler at all times. Keep the boiler area clean and free of fire hazards. • All 3WOOD Boilers must be connected to a tile-lined flue with a minimum size of 8”x 8” or to an insulated metal chimney with a minimum size of 6”. NO OTHER APPLIANCE SHOULD BE VENTED THROUGH THIS FLUE! Your chimney flue should be inspected regularly (BI-Monthly) for any build up of fly ash or creosote. • It is the responsibility of the installing contractor to see that all controls are correctly installed and are operating properly when the installation is completed. • Please read the literature and warranty supplied by the manufacturer of the various accessory devices. • These devices are warranted by the manufacturer, not by QHT, Inc. or BIASI. These accessory devices must be installed and used according to the recommendations of the manufacturer. • Do not use self contained, non-electrical zone valves in the zone controlled by the overheat control. • When references are made to tapping numbers, please refer to the specifications sections. • All firewood used in this boiler must be dried to moisture content of 20% or less. (see pg. 11) • Homeowners should read and familiarize themselves with “Procedure In Event Of Power Failure”. (see pg.9) • Anyone who is going to operate this boiler MUST read and familiarize himself or herself with “Starting And Maintaining A Fire”, (see pg.23) A DANGER COAL FIRES...