Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
3 Patent No. 6,904,873; Other patent pending Do not store or use gasoline or other flammable vapors and liquids do so may Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's , service agency or the gas This manual should be maintained in legible condition and kept adjacent to the heater or in another safe place for FlexGas™ NOTE: THIS MANUAL IS SUPPLEMENTAL FOR THE FLEXGAS MODELS OF THE HI DELTA HEATERS. THIS MANUAL ADDRESSES THE SPECIFIC DIF- FERENCES BETWEEN THESE HEATERS AND STANDARD HI DELTA MODELS. Please refer to the standard Installation and Operating Instruction manuals (Catalogs 1000.501 and 1000.511 as appropriate) for installation requirements which are not related to the gas supply. FlexGas™ NOTE: THIS MANUAL IS SUPPLEMENTAL FOR THE FLEXGAS MODELS OF THE HI DELTA HEATERS. THIS MANUAL ADDRESSES THE SPECIFIC DIF- FERENCES BETWEEN THESE HEATERS AND STANDARD HI DELTA MODELS. Please refer to the standard Installation and Operating Instruction manuals (Catalogs 1000.501 and 1000.511 as appropriate) for installation requirements which are not related to the gas supply. Rev. 3 reflects the following: Changes to: step 4 of the FlexGas System Start-up section on page 7; the Wiring Diagram was moved from page 5 to page 9; the addition of: a note to the Attach Manometers to Measure Pressures section on page 7. 2 WARNING: Do not use this heater if any part has been under water. Immediately call a qualified service technician to inspect the heater and to replace any part of the control system and any gas control which has been under water. WARNING: Should overheating occur or the gas supply valve fail to shut off, do not turn off or disconnect the electrical supply to the heater. Instead, shut off the gas supply at a location external to the heater. WARNING: Risk of electrical shock. More than one disconnect switch may be required to de-energize the equipment before servicing. WARNING: This FlexGas heater is intended for operation on Natural Gas as the primary fuel. DO NOT use this heater on Propane Gas as the primary fuel. Raypak strongly recommends that this manual be reviewed thoroughly before installing your Hi Delta heater equipped with FlexGas. Raypak also recommends that the appropriate Hi Delta Installation and Operating Instruction manual (1000.501 for 302B902B or 1000.511 for 992B – 2342B) be thoroughly read before attempting to install these heaters. Factory warranty does not apply to heaters that have been improperly installed or operated. (Refer to the warranty at the back of the standard Hi Delta manuals.) Installation and service must be performed by a qualified installer, service agency or gas supplier. If, after reviewing these manuals, you still have questions which these manuals do not answer, please contact the manufacturer or your local Raypak representative. Thank you for purchasing a Raypak product. We hope you will be satisfied with the high quality and durability of our equipment. Model Identification The model identification number and heater serial number are found on the heater rating plate located on the lower right outside jacket of the heater. The model number will have the form H9 1262BD or similar depending on the heater size and configuration. The letter(s) in the first group of characters identifies the application (H = Hydronic Heating, WH = Domestic Hot Water (DHW), P = Pool). The number which follows identifies the firing mode (1 or 4 = on-off, 3 = 2-stage, 8 = 3-stage and 9 = 4-stage). NOTE: Not all these firing options are available on all heaters. Refer to the Hi Delta manual for available firing options. The second group of characters identifies the size of the heater (four numbers representing the approximate MBTUH input), and, where applicable, a letter, indicating the manufacturing series. The final character is the letter “D” which designates the heater as a FlexGas equipped heater. Model Input (MBTUH) Pipe Size (Nat) Pipe Size (LP) 302BD 300 1-1.4” 3.4” 402BD 399 1-1.4” 3.4” 502BD 500 1-1.4” 3.4” 652BD 650 1-1.4” 3.4” 752BD 750 1-1.4” 1-1.4” 902BD 900 1-1.4” 1-1.4” 992BD 990 2” 1-1.4” 1262BD 1260 2” 1-1.4” 1532BD 1530 2” 1-1.4” 1802BD 1800 2” 1-1.4” 2072BD 2070 2” 1-1.4” 2342BD 2340 2” 1-1.4” Table 1: FlexGas Specifications Ratings and Certifications Standards: • ANSI Z21.13 · CSA 4.9 - latest edition, Gas-Fired Hot Water Boilers • CAN 3.1 - latest edition, Industrial and Commercial Gas-Fired Package Boilers • ANSI Z21.56 · CSA 4.7 - latest edition, Gas-Fired Pool Heaters • ANSI Z21.10.3 · CSA 4.3 - latest edition, Gas Water Heaters 3 4 All Raypak heaters are National Board Approved, and design-certified and tested by the Canadian Standards Association (CSA) for the U.S. and Canada. Each heater is constructed in accordance with Section IV of the American Society of Mechanical Engineers (ASME) Pressure Vessel Code, and bears either the ASME “H” stamp for boilers or “HLW” stamp for water heaters. The heater also complies with the l...