Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The smaller log will rest on front log against the "knot" on the left. See Figure 26. 6. Place lava rock around base of heater. Do not put lava rock on logs on burner. Front Log (#4) Grate Fingers Notches Figure 25 - Installing Front Log (#4) Figure 26 - Installing Log Piece (#5) Peg Log Piece (#5) Continued 16 107123 VENT-FREE NATURAL GAS LOG HEATER For more information, visit Dual Burner Biltmore Split Oak Models WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury. INSTALLATION Continued CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to High, check to see if flames contact any log. If so, reposition logs according to the log installation instructions in this manual. Flames contacting logs will create soot. Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater. 1. Place the front log (#1) on the grate fingers. Make sure the front log rests firmly between the grate fingers and the grate base (see Figure 27). 2. Place the base of the middle log (#2) in the U-shaped slots of the grate base. The cutout on the right of the middle log should fit over the burner (see Figure 28). Make sure the front of the middle log is resting on the tabs of the grate base. 3. Locate pegs on the bottom of back log (#3). Slide these pegs into the holes in the grate base behind the burner (see Figure 29). Figure 27 - Installing Front Log (#1) (CCL3930NTA Shown) Figure 28 - Installing Middle Log (#2) (CCL3930NTA Shown) Figure 29 - Installing Rear Log (#3) (CCL3930NTA Shown) Figure 30 - Installing Crossover Log (#4) (CCL3930NTA Shown) Figure 31 - Installing Crossover Log (#5) (CCL3930NTA Shown) Middle Log (#2) Tab Burner U-Shaped Slot Hole in Grate Base Front Log (#1) Grate Fingers 4. Locate holes on the bottom of crossover log (#4). Slide front hole onto the left peg (CCL3924NT or CCL3930NTA) or middle peg (CCL3018NT) on the middle log (#2) and the peg on the back log (#3). See Figure 30 for placement. 5. For CCL3924NT and CCL3930NTA Only: Locate peg and hole on the bottom of crossover log (#5). Slide the peg into the hole located in crossover log (#4). Slide the hole onto the peg on front log (#1). See Figure 31. For CCL3018NT Only: Locate holes on the bottom of crossover log (#5). Slide the holes over the left pegs on middle log (#2) and front log (#1). See Figure Grate Base Pegs Burner Log #2 Log #3 Pegs Crossover Log (#4) Front Log (#1) Log #4 Crossover Log (#4) Front Log (#1) Figure 32 - Installing Crossover Log (#5) (CCL3018NT Only) 107123 17 OWNER’S MANUAL For more information, visit Single Burner Mountain Oak Models INSTALLATION Continued WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury. Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater. 1. Place the back log (#1) onto the back of the burner. Make sure the log sits down into the hole in the grate and leans forward onto the two posts in front of the log (see Figure 35). 2. Locate the notches on the underside of the front log (#2). Also notice the recesses on the back of log #2. Slide the notches over the tabs on the grate base and the front posts into the recesses on the back (see Figure 36). 3. Place the crossover log (#3) on top of the back log and front log. Make sure the crossover log is seated into the notches on top of the back and front logs (see Figure 37). 4. Add lava rock around base of heater. Do not put lava rock on logs or burner. Figure 35 - Installing Back Log Crossover Log (#3) Figure 36 - Installing Front Log Front Log (#2) Notch Notch Tabs on Grate Base Notch Figure 37 - Installing Crossover Log Back Log (#1) Recess Post Hole in Grate Post 7 6 Figure 33 - Installing Crossover Log (#6) (CCL3930NTA Shown) Figure 34 - Installing Crossover Log (#7) to Model CCL3930NTA Only Pegs Log #2 Front Log (#1) Middle Log (#2) Crossover Log (#6) Holes Pegs 32. 6. Locate holes on the bottom of crossover log (#6). Slide these holes onto the right pegs located in middle log (#2) and front log (#1). See Figure 33. 7. For CCL3930NTA only: Locate holes on the bottom of crossover log (#7). Slide onto the pegs located in crossover log (#6) and middle log (#2). See Figure 34. 8. Add lava rock around base of heater. Do not place any lava rock on logs or burner. VENT-FREE NATURAL GAS LOG HEATER OPERATING HEATER Manually-Controlled Models FOR YOUR SAFETY READ BEFORE...