Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
KAWASAKI JET SKI® is a trademark of Kawasaki Heavy Industries, Ltd. registered in Australia. Quick Reference Guide General Information 1 j Periodic Maintenance 2 j Fuel System (DFI) 3 j Engine Lubrication System 4 j Exhaust System 5 j Engine Top End 6 j Engine Removal/Installation 7 j Engine Bottom End 8 j Cooling and Bilge Systems 9 j Drive System 10 j Pump and Impeller 11 j Steering 12 j Hull/Engine Hood 13 j Electrical System 14 j Storage 15 j Appendix 16 j This quick reference guide will assist you in locating a desired topic or procedure. •Bend the pages back to match the black tab of the desired chapter number with the black tab on the edge at each table of contents page. •Refertothesectionaltableofcontents for the exact pages to locate the specific topic required. STX-15F JET SKI® Watercraft Service Manual All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic mechanical photocopying, recording or otherwise, without the prior written permission of Quality Assurance Department/Consumer Products and Machinery Company/Kawasaki Heavy Industries, Ltd., Japan. No liability can be accepted for any inaccuracies or omissions in this publication, although every possible care has been taken to make it as complete and accurate as possible. The right is reserved to make changes at any time without prior notice and without incurring an obligation to make such changes to products manufactured previously. See your JET SKI® watercraft dealer for the latest information on product improvements incorporated after this publication. All information contained in this publication is based on the latest product information available at the time of publication. Illustrations and photographs in this publication are intended for reference use only and may not depict actual model component parts. © 2003 Kawasaki Heavy Industries, Ltd. Second Edition (1):Oct. 15, 2004 (K) LIST OF ABBREVIATIONS A ampere(s) lb pound(s) ABDC after bottom dead center m meter(s) AC alternating current min minute(s) ATDC after top dead center N newton(s) BBDC before bottom dead center Pa pascal(s) BDC bottom dead center PS horsepower BTDC before top dead center psi pound(s) per square inch °C degree(s) Celsius r revolution DC direct current rpm revolution(s) perminute F farad(s) TDC top dead center °F degree(s) Fahrenheit TIR total indicator reading ft foot, feet V volt(s) g gram(s) W watt(s) h hour(s) . ohm(s) L liter(s) Read OWNER’S MANUAL before operating. MAINTENANCE AND ADJUSTMENTS Maintenance, replacement, or repair of the emission control devices and systems may be performed by any marine Sl engine repair establishment or individual. EMISSION CONTROL INFORMATION Fuel Information THISENGINEISCERTIFIEDTOOPERATEONUNLEADEDREGULARGRADEGASOLINE ONLY. Aminimumof87octaneoftheantiknockindexisrecommended. Theantiknockindexisposted on service station pumps. Emission Control Information To protect the environment in which we all live, Kawasaki has incorporated an exhaust emissioncontrolsystemincompliancewithapplicableregulationsoftheUnitedStatesEnvironmental Protection Agency. Exhaust Emission Control System This system reduces the amount of pollutants discharged into the atmosphere by the exhaust of this engine. The fuel, ignition and exhaust systems of this engine have been carefully designed and constructed to ensure an efficient engine with low exhaust pollutant levels. Maintenance Proper maintenance and repair are necessary to ensure that watercraft will continue to have low emission levels. ThisServiceManualcontains those maintenance and repair recommendations for this engine. Those items identified by the Periodic Maintenance Chart are necessary to ensure compliance with the applicable standards. Tampering with Emission Control System Prohibited Federal law prohibits the following acts or the causing thereof: (1) the removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement, of any device or element of design incorporated into any new engine for the purposes of emission control prior to its sale or delivery to the ultimate purchaser or while it is in use, or (2) the use of the engine after such device or element of design has been removed or rendered inoperative by any person. Among those acts presumed to constitute tampering are the acts listed below: Do not tamper with the original emission related parts. * Digital Transistor Ignition System * Fuel Pump * Spark Plugs * Throttle Body and Internal Parts * Fuel Injectors *ECU Foreword This manual is designed primarily for use by trainedmechanicsinaproperlyequippedshop. However,itcontainsenoughdetailandbasicinformationtomakeitusefultotheownerwhodesirestoperformhisownbasicmaintenanceand repair work. A basic knowledge of mechanics, the proper use of tools, and workshop procedures must be understood in order to carry out maintenance and repair satisfactoril...