Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
A compatible stereo computer grapics or video system must be available to check the operation of the eyewear. To activate the eyewear, unfold the temple pieces; to turn off the eyewear, fold the templepieces. When not in use, fold your CrystalEyes CrystalEyesCrystalEyesCrystalEyesCrystalEyesCrystalEyes eyewear with the temples laying flat across the back of the lenses for convenient storage. Always AlwaysAlwaysAlwaysAlwaysAlways fold foldfoldfoldfoldfold the thethethethethe eyewear eyeweareyeweareyeweareyeweareyewear when whenwhenwhenwhenwhen not notnotnotnotnot in ininininin use useuseuseuseuse to tototototo maximize maximizemaximizemaximizemaximizemaximize the thethethethethe battery batterybatterybatterybatterybattery life. life.life.life.life.life. Installing the StereoGraphics Emitter StereoGraphics CrystalEyes CrystalEyesCrystalEyesCrystalEyesCrystalEyesCrystalEyes requires the use of an infrared emitter in order to synchronize the eyewear in conjunction with the left and right image sequence on screen. The I/R receiver (located in the center of the eyewear) must be in line of sight and in range of the emitter for successful operation of CrystalEyes. Please consult the documentation accompanying your emitter for installation and operation details. In all cases except for non-stereo-ready PCs, the system or graphics card manufacturer requires specific display settings to enable Stereo3D mode. Please consult the manual or vendor for your specific graphics subsystem to determine the proper settings for Stereo3D mode. For best results in using CrystalEyes CrystalEyesCrystalEyesCrystalEyesCrystalEyesCrystalEyes with standard workstation displays, set the emitter slightly behind the top edge of the monitor, as shown in Figure 1. In addition: • For EPRO, ESGI and ELR emitters, make sure the emitter is switched to the ON position. Depending on the emitter range needed, switch the emitter to either the high or low setting. • The ENT emitter will switch on and off automatically whenever a sync signal is presented by the graphics card. • Users of the EPC-2 must switch the emitter from BYPASS to STEREO MODE and set the emitter range separately. Figure 1. Display and Emitter Prescription Glasses If you normally wear prescription eyeglasses, place CrystalEyes CrystalEyesCrystalEyesCrystalEyesCrystalEyesCrystalEyes over them. The eyewear will fit comfortably over most prescription eyeglass frames. For more information on setting up your system, please refer to our website at Specifications Optics Shutters: liquid crystal Transmittance: 32% typical Dynamic Range: 1000:1 typical Close Time: Less than 0.2 milliseconds Open Time: Less than 3 milliseconds Field Rate: 80 to 160 fields per second Bright Mode: Automatically selected Infrared Sensor Angle of View: 90 degrees horizontal 140 degrees vertical Weight 3.3 oz. (93 grams) Controls On/Off: On/Off:On/Off:On/Off:On/Off:On/Off: Eyewear operation is switched on and off by unfolding and folding the eyewear temple pieces. Bright BrightBrightBrightBrightBright mode modemodemodemodemode: Both lenses automatically switch to full transparency for up to 8 minutes when shielded from infrared signals. Restoring the infrared signal returns the eyewear to full operation. Batteries Two 3 V lithium/manganese dioxide (NEDA 5004L), including: Eveready Maxell E-CR2032 CR2032 Sanyo Seiko CR2032 CR2032 Panasonic CR2032 Technacell CR2032 Ray-O-Vac CR2032 Varta CR2032 Saft LM2032 Duracell DL2032 Maintenance Your CrystalEyes CrystalEyesCrystalEyesCrystalEyesCrystalEyesCrystalEyes eyewear will provide years of excellent viewing if properly cared for. As with any eyewear, take care to prevent scratching the lenses. Also, protect the electronic circuits within the eyewear from damage by excessive moisture or immersion in liquids. Cleaning CrystalEyes CrystalEyesCrystalEyesCrystalEyesCrystalEyesCrystalEyes lenses have hard-coated plastic surfaces and if cared for properly will remain in good condition for many years. Using a soft cloth or lens tissue intended for plastic lenses, gently wipe the lens surface. A dry, clean chamois cloth also works well. CrystalEyes CrystalEyesCrystalEyesCrystalEyesCrystalEyesCrystalEyes eyewear lenses should receive the same care used for plastic eyeglass lenses except: n nnnnot otototot i iimmerse A Ammerse AAmmerse Avoid voidvoidvoidvoid spraying sprayingsprayingsprayingspraying d ddirectly irectlyirectly y yyour T Tourour The hehe use o ouseuse of ffDo DoDoDoDoDo not immerse immerseimmerseimmerse the thethethethethe eyewear eyeweareyeweareyeweareyeweareyewear in ininininin w wwwwwater ateraterateraterater or ororororor liquid. liquid.liquid.liquid.liquid.liquid. Avoid spraying cleaner cleanercleanercleanercleanercleaner directly directlydirectlydirectly on ononononon your youryouryour e eeeeeyewear. yewear.yewear.yewear.yewear.yewear. The u uTheTheThe uuse sesese of ofofof excess excessexcessexcessexcessexcess moisture moisturemoi...