Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
The unit’s memory can store up to four fingerprints. • The term “enroll” refers to scanning the fingerprint so the device will recognize the user. • The term “swipe” refers to the movement of the finger across the sensor strip. • The term “LED” stands for Light Emitting Diode. There are 6 LEDs located on the Fingerprint Keyless Entry. When unit is on, it is programmed to shut off after a short period of time. The unit’s sensor strip is sensitive so it is important to read the Tips for Success before attempting to use the Fingerprint Keyless Entry. Carton Inventory Receiver Fingerprint Keyless Entry ENROLL SEND ENROLL PASS FAIL READY RETRY Step 1 Install the Receiver 1. Unplug the opener before proceeding. 2. OPEN RECEIVER: Insert a small screwdriver in slot on receiver front panel as shown. Twist up actuator cover. 3. CONNECT RECEIVER AND OPENER: Remove about 1/4" (6 mm) of insulation from each end of the 2-strand bell wire. Connect one end to the receiver screw terminals (polarity is NOT required). Route wire along the channels and out the bottom as shown. 4. Connect the other end of the bell wire to the two opener terminals labeled “2” (white) and “1” (red), “common” and “command” or the terminals used for the push button control. 5. Use insulated staples to secure bell wire between receiver and opener. Length of bell wire depends on where the receiver will be installed. Replace actuator cover. 6. Choose a 120Vac polarized outlet for the receiver which is OUT OF THE REACH OF CHILDREN. Plug receiver into selected outlet. Return power to the opener. Actuator Cover Power Indicator Light Terminals Bell Wire Channels“SMART” Indicator Light Connect Bell Wire To Garage Door Opener Terminals “SMART” Actuator Bell Wire To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is not connected BEFORE installing the receiver. To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: • Install Keyless Entry Control within sight of the garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from all moving parts of door. • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. NOTICE TO U. S. CONSUMERS: Some states prohibit the service or repair of garage door openers which cannot be made to comply with the safety standards contained in UL 325 (1988 revision). In order to comply with both the letter and the spirit of these laws, this universal radio control should not be used with any LiftMaster®, Chamberlain®, or Sears Craftsman® garage door opener manufactured prior to April 1, 1982. To find out if your Chamberlain-made garage door opener was manufactured prior to or after April 1, 1982, please call 1-800-528-9131 before installing this universal radio control. Step 2 Install the Keyless Entry 1. Remove cover. 2. Fasten bottom screw to mounting surface. Allow 1/8" (3 mm) to protrude above surface. Position unit on screw head and adjust for snug fit. 3. Fasten top screw. Replace cover. 1 3 2 CORRECT 1. Make sure finger is clean and dry. Place finger flat above the sensor strip with the top knuckle above the sensor. 2. Swipe finger straight down keeping firm contact with the sensor. The swipe should be a slow, constant speed. SPECIAL NOTES: Use the same finger for every swipe. It is important to swipe finger slowly and firmly as this is the reason most swipes fail. Swipe finger straight down keeping firm contact with Start swipe with the sensor. the top knuckle above the sensor strip. Sensor Strip Sensor Strip The scan should end at the tip of finger. INCORRECT • Do not bend finger during swipe as this will only scan the tip of your finger. • Swipe finger straight down, not at an angle. • Swipe flat, not tilted or rolled to one side. Reference Cover Resend button:When pressed the door will stop if Enroll button:When moving up or reverse if pressed the unit will gomoving down. into Enroll mode. Send LED (yellow): Lit after a passed fingerprint Enroll LED (yellow): scan and indicates that the Lit when the unit is in Resend button is active Enroll mode. and can be used to stop ENROLL SEND ENROLL Fail LED (red): Lit when or reverse door travel. PA S S FAIL READY RETRY a scanned fingerprint Pass LED (green): Lit when does not match a a scanned fingerprint stored print. Sensor Strip matches a stored print. Retry LED (yellow): Lit when another swipe is Ready LED (green): Lit required. when unit is ready to scan fingerprint. Extra directions are located on the inside of cover. Step 3 Enroll Initial User NOTE: The unit requires 3 passed swipes to enroll a user. 1. Open cover to turn unit on. Wait until Enroll LED and Ready LED are lit (not 1 flas...