Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
DISARMING BUTTON 2 BUTTON 1 BUTTON 1 + 2 = BUTTON 4 (NO BUTTON 3 WITH WATCH) To disarm the alarm and unlock the doors, press the #2 Button on either transmitter. You will hear 2 siren chirps and the lights will flash twice. The in-dash LED stops flashing dome light turns on. (Optional) If the alarm is tripped, then the #2 Button will have to be pressed twice. The first press will reset the trigger and the second press will Disarm. OPERATION OPERATION ALARM CYCLE RESET If and when the alarm system is triggered, pressing the #2 button on either transmitter will reset the unit’s cycle (lights, siren) condition without disarming it. Pressing the button a #2 button second time will Disarm/Unlock the system. REMOTE AUX. OUTPUT 1 (OPTIONAL,) Note: AUX 1cannot be operated with the SecurWatch transmitter if the alarm system is programmed for Carjack protection. To activate an optional feature such as a trunk/hatch pop (if vehicle is properly equipped), press Button #3 (AUX) on the 4-Button CoolGlow remote or press and hold Button #2 (when disarmed) on the SecurWatch® transmitter. This provides a . second auxiliary pulse to activate a relay for power trunk release or other optional feature. (Extra parts and/or labor may be required for this feature.) REMOTE PANIC PROTECTION To sound the alarm upon command (panic), press and hold the Button #1 on either transmitter for at least 3 seconds until the siren sounds and lights flash. Press Button #2 to reset the panic mode. ARMING WITHOUT SHOCK SENSOR To arm the alarm without Shock sensor protection, press Button #1 as normal then press and hold Button #4 (SLNT) for about 3 seconds until the unit flashes the lights 3 times indicating shock sensor bypass. (Button #1, then 1+2 w/Watch) SHOCK / IMPACT PROTECTION WITH PRE-WARNING Once the system is armed, if a low-level shock to the vehicle body is detected, the pre-warning sensor activates with 5 siren chirps and one light flash as a Warn-Away feature. If a hard impact to the vehicle is detected the system will go into a full trigger cycle for 20 seconds. Adjust the shock sensor as needed by turning the control knob clockwise or counter-clockwise to increase or decrease the sensitivity. Shock sensors will “settle in” over time and it may take a few tries over a few weeks to get the adjustment correct for your vehicle. We recommend a moderate adjustment where the vehicle is protected but it is not constantly triggering from the slightest vibration therefore creating a nuisance. EMERGENCY OVERRIDE/DISARM If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to open the door with the key, (activating the alarm), turn the ignition ON, press and hold the override/program until the system disarms (about 7 seconds). The Alarm will disarm allowing you to operate the vehicle until you can repair/replace the remote transmitter. VALET MODE To put the Alarm system into valet mode for vehicle service or otherwise, turn the ignition on and press the Button #4 (SLNT) on the remote until lights flash 3 times. The in-dash LED turns on solid. Repeat the procedure to exit VALET mode. The system will chirp 3 times and the LED will turn off on Valet mode exit. Lock/Unlock and AUX features will still operate in when in VALET mode. (IGN ON, then Buttons 1+2 w/Watch) OPERATION OPERATION SILENT ARM/DISARM Use Button #4 (SLNT) for silent arm and disarm (Chirp Defeat). Press and release Button #4 to arm/disarm without the siren chirp. The light flash will be your only confirmation on Arm/Disarm. (Buttons 1+2 w/Watch) PASSIVE ARMING / PASSIVE LOCK MODES If programmed, passive (Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The lights will flash twice when the last door is closed and the LED will begin flashing rapidly while counting down. If a door is reopened the countdown will reset and, the system will wait for the door or zone to close before starting 30 second countdown again. The unit will chirp once and flash the lights once. Doors will lock if passive locking is selected. May qualify for insurance discounts-check with your agent or proprietor. See Jumper Plug programming for J1 Passive Arm and J2 Passive Lock settings. PRIOR INTRUSION ALERT If the system was tripped in your absence, the dash LED will be flashing rapidly. When the system is disarmed you will hear 2 chirps, a pause then 4 chirps. Carefully inspect your vehicle to see if there is any damage or a theft has occurred. DOME LIGHT ILLUMINATION (OPTIONAL) This feature turns on the vehicles dome light upon disarm for 30 seconds or until the key is inserted and turned on. This will provide illuminated entry to your vehicle at night or in dimly lit areas for safety and security. (Extra parts and/or labor may be required for this feature.) DOOR OPEN WARNING If the system detects a faulty or open zone (Door left open) when the system is armed with a remote, it will trigger 5 within ...