Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
This booklet contains the information necessary for installing, using, and maintaining your 2004TW1 or 2004DC alarm system. any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below. This installation book is designed for the installer or with an existing understanding of automotive systems, along with the ability to test and connect To ease installation, we suggest that you READ THIS MANUAL before beginning your This book is provided as a GENERAL GUIDLINE the information contained herein may differ *IMPORTANT INFORMATION: Primary and Optional Features -PRIMARY: These are features that must be connected order for the system to operate properly L.E.D., Power, Ground, Door Pin, -OPTIONAL: These are features are to be installing dealer (i.e. Door Locks, Protection and Auxiliary Remote features may also require Consult with your installer what is going to be installed TECH SUPPORT (800) 998-6880 Hours: M-F 8: Pacific REV B 03.2004 Text Box: This device complies with FCC Rules part 15. Operation is subject to the following two conditions: 1) This device may not cause interference, and (2) this device must accept any interference that may be received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. Such modification could void the user's authority to operate the equipment. Text Box: Text Box: SERIES II TABLE OF CONTENTS Installation Cautions & Warnings…….……………………………………………………………...……………… Suggested Component Mounting………….…………………………………………………………….…………..3 Wiring……..……………………………………………………………………………………………………………. Power Door Lock Wiring...………………………………………………………………..………………………… Starter Disable Wiring…………………………..…..…………………………………………………………..…….. System Wiring Diagram………………….…………………………………………………………………….……… CS-2004TW1 Antenna Diagram………...…………………………………………………………………….…...… Option Programming……………..………………………………………………………..…………..…….…… Programmable Option Reset………………………...……….……………………………………………………... Remote Programming……..……………………………………………………..………………………....……. Operation, 2-Vehicle Control (CS-2004DC II Only),…………………………………..….……………….….. Carjack Operation……………………………………………………………………………..……..…………….. INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service BAGS, ABS BRAKES, AND BATTERY). TO PREVENT A POSSIBLE DEAD remove vehicle dome light fuse CERTAIN TO REINSTALL FUSE DO NOT EXCEED MAXIMUM SERIOUS DAMAGE MAY FUNCTIONS ARE LISTED REMOVE MAIN SYSTEM before jump starting the battery MAY OCCUR TO DO NOT ROUTE with brake, and or any other Text Box: 2 CONTROL MODULE / COMPONENT MOUNTING DO NOT Mount the control unit or wiring harness in the engine compartment or anywhere they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column. The alarm control module should be mounted in a concealed location. The antenna wire should be routed away from any metal if possible. Do not alter the length of the antenna, ground it, or route it with other wires. SIREN MOUNTING: Mount the siren under the hood to fender-well or other body surface with the open end facing downward. Run the red siren wire through the firewall using a rubber grommet. LED: Mount the LED in a visible location on the dashboard or console. Shock Sensor: Mount the included shock sensor with wire ties to an under dash wire harness or fasten with screws to firewall or side paneling. Override/Program Button: Mount the Override/Program push-button in a hidden but accessible location. It is used for emergency disarm without the use of the transmitter and for WIRING RED WIRE: +12V POWER INPUT (15 Amp Fuse) Connect to a +12 Volt source with the supplied fuse and fuse-holder. We recommend the connection Vehicle’s Battery Positive Terminal. BLACK WIRE: CHASSIS GROUND THIS WIRE MUST BE CONNECTED TO OF THE VEHICLE. Scrape away any paint to ensure a good connection. YELLOW WIRE: IGNITION SWITCHED Connect to a (+) Ignition wire that the key is in both the “ON” and ORANGE WIRE: (-) NEGATIVE This wire becomes a Negative when system is armed. disable relays or to activate WHITE WIRE: +12V OUTPUT (10A) Connect to the switched front of the vehicle. BROWN WIRE: Connect Text Box: 3 WIRING BLUE WIRE: (-) HOOD/TRUNK TRIGGER The Blue wire is used for a grounding hood pin switch, trunk pin or both. Connect to existing hood and trunk pin switches that read ground when open. If no existing switches are available, install new GREEN WIRE: (-) DOOR TRIGGER Connect to Negative type door switches that read ground when a door is opened and 12 volts when all doors are closed. In the case of isolated door triggers, you may need to run additional wires from other doors OR go directly to the dome light. VIOLET WIRE: (+) DOOR TRIGGER Connect to Positive type door switches that show +12 Volts when the closed. PINK WIRE: ...