Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Reset Switch Turn on the power while pushing this switch using a sharp object. Continue to push the switch for 5 seconds or more to restore all factory settings except for the date and time. SD card cover Audio input terminal (dual LINE IN and MIC IN) • • Installing the Camera Before installing the camera, set the IP address and other network information on the camera using the “VB Initial Setting Tool” on the Setup CD-ROM. For details on how to operate the “VB Initial Setting Tool,” see “VB-M700F/VB-M600D/VB-M600VE Operation Guide”. 1 Mount the camera to the mounting bracket Use the mounting screw holes on the camera to fi x the camera to the mounting bracket. Important You must consult your retailer or provide the mounting bracket yourself. A tripod mounting screw (1/4-20 UNC) will fi t the fi xing screw hole. Be sure to use a mounting bracket with a mounting screw shorter than 5.5 mm (0.22 in.). Using a mounting bracket with a mounting screw 5.5 mm (0.22 in.) or longer may damage the camera. • • • 2 Connect the cables to the camera Connect the LAN cable. If an AC adapter PA-V17 (optional) or external power supply is used, connect the power connector to the camera. Connect cables to the external device I/O terminals and audio input/output terminals as necessary. 3 Set the camera angle When installation is complete, use the Camera Angle Setting Tool to check the image on the camera and manually adjust the camera angle. Zoom and focus can be adjusted with the Camera Angle Setting Tool (see “Camera Angle Setting Tool” in “VB-M700F/VB-M600D/ VB-M600VE Operation Guide”). 1 2 Connecting the Camera Power Connection Power can be supplied to the camera in the three ways described below. .. PoE (Power over Ethernet) The camera supports PoE functions. Power can be supplied to the camera by using a LAN cable to connect it to a PoE HUB that conforms to the IEEE 802.3af standard. Important Check with your Canon sales representative for more information about PoE HUB and Midspan technology. Some PoE HUBs allow current limits for each port, but applying limits may interfere with performance. If using this type of PoE HUB, do not limit the operating current. Some PoE HUBs have total consumption current limits for ports, which can interfere with performance when multiple ports are in use. For more information, check the instruction guide for your PoE HUB. Use a category 5 or higher cable 100 m (328 ft.) or less in length for the LAN cable that connects the camera and the PoE HUB. When the camera is connected to a switching HUB, changing the connection while the camera is operating may cause the HUB learning function to interfere with communication. Do not change the connection when the camera is operating. The camera can also be connected to an AC adapter (optional) while receiving power from a PoE HUB. In such cases, the PoE power supply is given priority, and the camera does not use the power supply from the AC adapter (optional). When the PoE power supply is disconnected, power is supplied automatically from the AC adapter (optional). Midspan (a LAN cable power supply device) is a device that, like a PoE HUB, supplies power to the camera via a LAN cable. • • • • • • .. External Power Supply 12 VDC or 24 VAC input can be used. Connect the bundled power connector as shown below. Screwdriver Tightening torque: 0.2 N·m (max) Strip Approx. 4 to 6 mm (0.16 to 0.24 in.) Power connector (bundled) For 12 VDC and 24 VAC input, use a power supply insulated from 100 VAC. 12 VDC can be connected in a non-polar confi guration. Important The power supply should be within the following voltage range. 24 VAC: Voltage fl uctuation within 10% of 24 VAC (50 Hz or 60 Hz ± 0.5 Hz or less) Current supply capacity of at least 1.0 A per camera 12 VDC: Voltage fl uctuation within 10% of 12 VDC Current supply capacity of at least 1.5 A per camera When using a 12-VDC battery power supply, be sure to connect resistors of at least 0.5 - 1.0 ./20 W in series to the power line. For an external power supply, use a double-insulated device. • • • • • Recommended Power Cables for VB-M700F [Reference] Cable (AWG) 24 22 20 18 16 Conductor diameter mm (in.) . 0.52 (. 0.020) . 0.65 (. 0.026) . 0.82 (. 0.032) . 1.03 (. 0.041) . 1.30 (. 0.051) 12 VDC maximum cable length m (ft.) 5 (16.4) 9 (29.5) 14 (45.9) 23 (75.5) 32 (105.0) 24 VAC maximum cable length m (ft.) 11 (36.1) 18 (59.1) 29 (95.1) 46 (150.9) 64 (210.0) Use UL cable (UL-1015 or equivalent) for 12 VDC or 24 VAC wiring. .. AC Adapter Use the dedicated AC adapter PA-V17 (optional). Note The camera does not have a power switch. Connecting and disconnecting the LAN cable (PoE power supply), AC adapter, or external power supply plug turns the power ON and OFF, respectively. When the camera needs to be rebooted, perform the reboot operation from the camera setting page (see “Maintenance” in “Setting Page” of the “VB-M700F/VB-M600D/VB-M600VE Operation Guide”). • • External Device I/O Terminals External device...