Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Also, the camera angle switches to this preset, and the new angle can be checked in Admin Viewer. (12) [Admin Viewer] button Launches Admin Viewer. Use this button if you want to set a preset while actually checking the image using Admin Viewer. Orient the camera to the position you want to set as a preset using Admin Viewer, and then click the [Get value] button and [Apply] button in this order to set the preset. (13) Status List Shows the result of communication between this tool and the camera. Warning messages are shown in blue, error messages in red. Note • Sending the edited results to the camera using the [Apply] button does not save the edited results in the camera. After confirming the edited results, be sure to click the [Save preset settings] button to save the settings in the camera. • If connection is made by entering the IPv6 address, Admin Viewer cannot be used on Internet Explorer 6. Setting the Preset A preset can be set in one of the following two ways. Select appropriate settings according to the environment in which the camera is operated or based on your preference. Note To use presets in VB-C60 Viewer, unselect the [Not shown in viewers] check box. VBAdmin 2-25 Preset Setting Tool • Changing Settings in Preset Preview Frame Use the preview frame on the panorama image to set presets. How to Set 1. Select the preset you want to set from the preset selection box, and then fill the [Preset name] field. Be sure to enter the preset name (single-byte alphanumerics). 2. Drag to move/resize the preset preview frame displayed on the panorama image to set the preset. Clicking on the image moves the preview frame until the clicked point becomes the center. At this time, you can also edit the camera parameter values to fine-tune the set position. 3. Click [Apply]. Confirm on the status list that the settings have been applied correctly, and then click the [Save preset settings] button to save the settings in the camera. Preset Setting Tool • Changing Settings from Camera Angle in Admin Viewer Launch Admin Viewer and set its viewing angle as a preset. How to Set 1. Select the preset you want to set from the preset selection box, and then fill the [Preset name] field. 2. Click the [Admin Viewer] button to launch Admin Viewer. User authentication is required to access Admin Viewer (.. P. xiv). 3. Click "Obtain/release Camera Control" button on Admin Viewer to obtain the control privileges of the camera. 4. Operate the camera to adjust to a desired position, and then click the [Get value] button. The loaded values can be checked by the camera parameters or in the preset preview frame. At this time, you can also edit the camera parameter values to fine-tune the set position. VBAdmin 2-27 Preset Setting Tool Preset Setting Tool Click [Apply]. Check the status list to make sure the settings have been applied correctly, and then click the [Save preset settings] button to save the settings in the camera. Note • The preview based on the panorama preview function may vary slightly from the actual image. After setting a preset, be sure to confirm with Admin Viewer that the preset has been reflected correctly. • To apply the manual focus mode, manually adjust the focus while checking the actual image using Admin Viewer. After the focus has been adjusted, set the focus using the [Get value] button. • If the image stabilizer setting is changed after a preset has been set, the set viewing angle will no longer agree with the viewing angle during operation (.. P. 3-22). If the image stabilizer setting has been changed, check the preset settings again. • If a dome housing is used, be sure to set presets with the dome installed. • If the camera mounting method has been changed, set presets again. Tip • Up to 20 presets can be set. • Changes to preset settings are not reflected in the connected viewer. • You can disable presets in VB-C60 Viewer by selecting the [Not shown in viewers] (.. P. 224) check box. • Preset positions cannot be set in the digital zoom area. • You can also set multiple presets and save them all at once using the [Save preset settings] button. Preset Setting Tool Preset Setting Tool Set a preset tour whereby the camera goes around and monitors the multiple presets currently set. • Display Screen "Preset Tour Setting Area" (6) (1) (2) (3) (7) (8) (9) (4) (5) (1) Tour schedule list A list of presets for which preset tour has been set is displayed. (2) [Add] button Add to the tour schedule list the preset you have set. (3) [Up] and [Down] buttons Select each preset in the list and click the [Up] or [Down] button to change the sequence of preset tour. In preset tour, the presets are checked one by one from the top. (4) [Delete] button Delete the selected preset. (5) [Preview] button Reflect the selected preset setting in the preset preview frame. Also, the camera angle switches to this preset, and the new angle can be checked in Admin Viewer. (6) Auto preset tour Select the timing of preset tour from ...