Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
ON: Turns on burst signal output. This is the factory default setting. OFF: Turns off burst signal output. Note: With some monitors and VCR models, output of a camera images in the black and white mode will not display a proper image unless a burst signal is provided. Select ON for this setting when using equipment that requires a burst signal. -29 (11) Auto Focus (AF MODE) 1. Move the cursor to AF MODE, and then tilt the joystick left or right to select an auto-focus mode setting. MANUAL S.M.L : Activates auto-focus when the AF button on the system controller is pressed. AUTO S.M.L : Auto focus is used automatically when PAN, TILT or ZOOM are used in manual operation. The letters S (Small), M (Medium), and L (Large) indicate the size of the auto-focus sensing area. The factory default setting is AUTO L. Notes: • The AUTO (S.M.L.) setting can be selected only when OFF, x2 FIX or x2 AUTO is selected for the electronic sensitivity enhancement (SENS UP). Any other SENS UP setting causes MANUAL (S.M.L.) to be selected automatically for the auto-focus mode (AUTO). • Zooming up from WIDE can cause the image to go out of focus. • Auto-focus may not be possible with the types of objects listed below. For such objects, focus manually. Example: • Shiny or high intensity objects • Objects shot through wet or dirty glass • Pictures that are a mixture of distant and nearby objects • White walls and other single-color objects • Venetian blinds and other vertically striped objects • Slanted objects • Objects illuminated with low lighting Auto-focus focuses on the object in the center of the picture, so objects around the outside periphery of the picture will not be in focus. (12) Zoom Limit (ZOOM LIMIT) 1. Move the cursor to ZOOM LIMIT, and then tilt the joystick left or right to select a zoom limit setting. When doing manual operation, zoom operation cannot go beyond the zoom limit. Optical zoom ranges from 1 to 30 magnifications, while digital zoom is used for higher magnifications (up to 300). The factory default setting is x30 (30x optical zoom). Notes: • If zoom limit is set to more than 30x, then zoom operation pauses at 30x magnification. • Increasing the zoom to over 30x magnification (digital zoom) decreases the resolution. • You cannot set a zoom magnification of greater than 30x as a preset position. (13) Auto Image Stabilizer (STABILIZER) This function electronically compensates for an unstable camera image due to movement of a mounting pole or bracket. 1. Move the cursor to STABILIZER, and then tilt the joystick left or right to turn the stabilizer on or off. The default setting is OFF ON : Automatically compensates for an unstable image. OFF : Image stabilizer will not operate. This is the factory default setting. Notes: • The stabilizer may not be effective for the following subjects. Example: • Objects illuminated with low lighting • Single-color objects (white walls etc) • Fast moving periodic action, such as mechanical vibration, may not be tracked. • The stabilizer does not work during PAN/TILT/ZOOM/FOCUS or when the camera setup menu is open. • When set to ON, some effective pixels on the edge of the CCD are used by the stabilization function. This may result in a small reduction in resolution and a narrower angle of view. After activating the image stabilizer function, check that the field of view is correct. • Image stabilization may not function where there is excessive camera movement or when the scene is low light or low contrast objects. -30 PAN/TILT SETTINGS ¦ Using the Pan/Tilt Setup Menu Display the pan/tilt setup menu from the setup menu to configure pan and tilt settings. First, display the pan/tilt setup menu. 1. Display the setup menu (page 25), move the cursor to PAN/TILT O, and then press the CAM (SET) button. This will display the pan/tilt setup menu. **PRESET POSITION** 1* 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 ID:DOOR 033-064 225-256 RET TOP 2. Move the cursor to the number you want to select, **PAN/TILT SETUP**1/2 PRESET 1 MAP HOME POSITION OFF SELF RETURN OFF AUTO MODE OFF AUTOPAN KEY AUTO PAN PATROL PRIVACY ZONE OFF IMAGE HOLD OFF DIGITAL FLIP ON PROPO.P/T ON 0w r yi! q e t u o and then press the CAM (SET) button. This registers the position number setting and displays the preset setting menu. (this page) To select a position number in the range of 033 to 064, move the cursor to 33-64 in the lower left corner of the menu, and then press the CAM (SET) button. 1 ! Preset numbers set subsequently are the same. **PAN/TILT SETUP**2/2 AREA TITLE ON(USER) TILT ANGLE 0° CLEANING OFF RET TOP ! 2 **PRESET POSITION** 3! 4 ! 33 34 35 36 37 41 45 49 53 57 61 ID: 38 42 46 50 54 58 62 39 43 47 51 55 59 63 40 44 48 52 56 60 64 4 * The following sections numbered q to !explain how to use each of the pan/tilt setup menu items. Notes: (1) Position Number Selection (PRESET) 065-096 001-032 RET TOP • An asterisk (*) to the right of a position number Positio...