Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
3. Press I(S) to determine the CAMERA ID. To erase all characters in the editing area Move the cursor to RESET and press I(S). All characters in the editing area disappear. To determine the display position of the CAMERA ID 1. Move the cursor to POSI, and press WV-CW474 Highlighted I(S). The display at right appears and the CAMERA ID is highlighted. 2. Move the CAMERA ID to the desired position by pressing I(L) / I(R) / I(U) / I(D). 3. Press I(S) to fix the position of the CAMERA ID. The mode returns to the previous CAMERA ID menu. Notes: • The CAMERA ID stops at the edges of the monitor screen. • The CAMERA ID moves faster if any of I(L) / I(R) / I(U) / I(D) is kept pressed for a second or more. 2. Light Control Setting (ALC) 2-1. ALC Mode with SUPER-D2 ON Super Dynamic2 Function (SUPER-D2) The important object in a scene is usually placed in the center of the monitor screen. In the SUPER-D2 mode, more photometric weight is given to the center of the screen (where the important object is located) than to the edge of the screen (where a bright backlight would most likely be located). The SUPER-D2 function eliminates interference by strong background lighting which makes the camera picture dark, such as a spotlight. 1. Move the cursor to ALC and press I(S). The ALC CONT menu appears. 2. Move the cursor to SUPER-D2 and select ON. 3. If you want to adjust the video output level, move the "I" cursor for LEVEL. Adjust to the desired level by pressing I(L) or I(R). ** ALC CONT ** BACK LIGHT COMP SUPER-D2 ON LEVEL ...I..... -+ RET END (To be continued reverse page) SETTING PROCEDURES 2-2. ALC Mode with SUPER-D2 OFF 1. Move the cursor to SUPER-D2 and select OFF. The MASK SET appears on the menu. 2. Move the cursor to MASK SET and press I(S). The 48 mask areas appear on the monitor screen. The cursor is blinking in the upper left corner of the screen. 3. Move the cursor to the area where backlight is bright and press I(S) to mask that area. The mask turns to Blinking white. (When the cursor is moved on an area that has already been masked, the mask and cursor start blinking.) 4. Repeat step 3 to mask the desired area. To cancel masking, move the cursor to that area and press I(S). 5. After masking is completed, pressI(S) for 2 seconds or more. The ALC CONT menu appears. 6. If you want to change the video output level (picture contrast), move the “I” cursor for LEVEL and adjust the level. Turns to white Blinking ** ALC CONT ** BACK LIGHT COMP SUPER-D2 OFF MASK SET LEVEL ...I..... -+ RET END . Blinking Note: If ON is selected for SUPER-D2, a shadow (black line) may appear at the boundary between the bright and the dim scene. This is a natural phenomenon and does not indicate trouble. 3. Shutter Speed Setting (SHUTTER) Note: To select electronic shutter speed, select OFF for SUPER-D2 in the ALC CONT menu. Move the cursor to SHUTTER and select the electronic shutter speed. The preset values for SHUTTER (electronic shutter speed) change by pressing I(L) or I(R) as follows: The factory default setting is ---. OFF 1/100 1/250 1/500 1/10000 1/4000 1/2000 1/1000 4. Gain Control Setting (AGC ON (DNR-L, DNR-H)/OFF) You can set the gain (brightness level portion of an image) to automatic level adjustment. Move the cursor to AGC and select automatic level adjustment ON (DNR-H), ON (DNR-L) or fixed level (OFF). ON (DNR-L): Selects lower noise reduction level. ON (DNR-H): Selects higher noise reduction level. OFF (Fixed Level): Disables the gain control function. The factory default setting is ON (DNR-H). Notes: • If ON (DNR-H) is selected for the AGC, the noise reduction function is automatically activated under low light conditions to reduce noise. In pictures containing a moving object, this may result in an afterimage. • DNR-L is recommended for pictures containing a moving object that results in an afterimage. However, the noise slightly increases. • DNR-H and DNR-L do not appear for AGC on the system controller setup menu. 5. Electronic Sensitivity Enhancement (SENS UP) There are two modes for SENS UP. AUTO: If you select X10 AUTO, for example, the sensitivity is automatically raised to X10 max. When AUTO is selected, AGC is automatically set to ON. FIX: If you select X32 FIX, for example, the sensitivity is raised to just X32. The factory default setting is OFF. Move the cursor to SENS UP and select the parameter for electronic sensitivity enhancement. The preset values for SENS UP (electronic sensitivity enhancement) change by pressing I(L) or I(R) as shown right: OFF X2 AUTO X4 AUTO X6 AUTO X10 AUTO OFF X32 FIX X16 FIX X10 FIX X6 FIX X4 FIX X2 FIX Notes: • When ON is selected for SUPER-D2 in the ALC CONT menu, FIX is not available for this item. • When you select AUTO for SENS UP and ON for SUPER-D2, the SENS UP function has priority so that the SUPER-D2 function is not activated automatically. • While the SENS UP function is selected, noise, spots or a whitish phenomenon may appear in the picture when the sensitivity of ...