Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Notes: • When set to ON, the available parameters for SHUTTER and SENS-UP will be limited as shown on the next page. • Set SUPER-D3 to OFF when noise in a bright portion, flickerings, or color deterioration are observed. 1. Select ALC for ALC/ELC on the CAM SETUP menu and press SET. > The ALC CONT menu opens. 2. Select ON for SUPER-D3. 3. Adjust the video output level (LEVEL) by moving the "I" cursor. It may be better to adjust LEVEL slightly higher. First, select a language for menu display and camera ID display. Language Setup (LANGUAGE SETUP) 1. Select LANGUAGE on the top menu and press SET. > The LANGUAGE SETUP menu opens. 2. Select a language. The default setting is English. Available languages: ENGLISH, FRANCAIS, DEUTSCH, ESPANOL, ITALIANO, eieeaaa, JAPANESE, CHINESE 3. Select SET on the menu and press the SET button. 1. Camera Identification Setting (CAMERA ID) Assign a name to the camera using up to 16 characters to display it overlaying on the camera picture in the selected position. Note: If you change the language selection after the assignment of camera ID, it will be erased. 1. On the CAMERA SETUP menu, select ONv or OFFv for CAMERA ID and press SET. ONv: Displays entered camera ID. OFFv: Does not display the ID. >The CAMERA ID menu opens. 2. Select a character from the character area and press SET. >The selected characters are displayed in the editing area. 3. Repeat these procedures until all characters are entered. • To enter a blank space, select SPACE and press SET. • To replace a specific character in the editing area: 1. Move the cursor to the editing area and then move the pointer to the character to be replaced pressing the L and R buttons. 2. Move the cursor to a candidate character in the character area and press SET. • To erase all characters of the camera ID, select RESET and press SET. 4 To specify the ID display position: 1. Select POSI and press SET. > The entered camera ID will be highlighted on the screen. 2. Move it into the appropriate position and press SET. > The position is determined and the screen will return to the CAMERA ID menu. Note: Keep pressing any of L/R/U/D for a second or more to move the camera ID faster as necessary. 2. Light Control Mode Setting (ALC/ELC) Select a light control mode depending on the lens type mounted. The default setting is ALC. ALCv: Is applicable to the auto iris lens. SUPER-D3 is available with this selection. ELCv: Is applicable to the fixed or manual iris lens. Cautions: 1. Under bright lighting conditions such as outdoors, use an ALC lens because the ELC control range is not wide enough under these conditions. 2. Use an ALC type lens if the following phenomena occur: • Strong smear and/or blooming on highlighted objects such as a spotlight or sunlight from windows. • Noticeable flicker in the picture and/or color rendition variations. 3. If ELC is selected, SUPER-D3 and SHUTTER are not available and the white balance mode is automatically set to ATW1 or ATW2 previously set. 4. If ELC is selected and a fixed iris lens is used, the focal depth becomes shallower than with the use of an ALC lens. Therefore, the range of focus-to-object distance becomes narrower. 2-1. ALC Mode with SUPER-D3 ON Super Dynamic 3 Function (SUPER-D3) In the SUPER-D3 mode, more photometric weight is given to the center of the screen than to the edge where a bright backlight would most likely be located. **CAMERA SETUP** 1/2 CAMERA ID OFF ALC/ELC ALC SHUTTER OFF AGC ON(HIGH) SENS UP OFF SYNC INT WHITE BAL ATW1 MOTION DET OFF DNR HIGH RESOLUTION HIGH BW MODE . . . . (To be continued reverse page) SETTING PROCEDURES **ALC CONT** BACK LIGHT COMP SUPER-D3 ON LEVEL ..I...... - + RET TOP END WV-CP480 Highlighted CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ SPACE POSI RET TOP END RESET ................ Character Cursor Pointer Character Area Command Editing Area Nighttime Daytime Nighttime Daytime SUPER-D3 ON SUPER-D3 OFF **LANGUAGE SETUP** LANGUAGE ENGLISH SET RET TOP END Opening/Closing the Setup Menu It is possible to open the WV-CP480 TOP menu by holding down the SET button for 2 seconds or more while displaying camera pictures. At first, the menu will be displayed in English. Move the cursor to SETUP DISABLE using the direction buttons and press the SET button to change it to SETUP ENABLE so that the menu becomes operable in selecting your language and other parameters. On the menu, you can check current settings and perform settings to meet requirements. To close the menu and return to camera picture, move the cursor to END and press the SET button. (When no operation is performed for 5 minutes, the menu will automatically close.) How to Set Up on the Menu Operate the direction buttons (U: Up, D: Down, L: Left, R: Right) and the SET button as shown in the table below. In the following pages, abbreviated expressions will be used many times for convenience. An abbreviated expression "Select CAMERA and press SET" means "Move the cursor to CAM...