Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
Turn the power off immediately and contact qualified service personnel for service. Do not rub your hands with the metallic edges. This could cause injury. Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Ask qualified service personnel for servicing. Handle the camera with care. Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage. Do not touch the dome cover with your bare hands. A dirty dome cover causes deterioration of picture quality. Cleaning the camera body Turn the power off when cleaning of the camera. Use a dry cloth to clean the camera. Do not use strong abrasive detergent when cleaning the camera body. When the dirt is hard to remove, use a mild detergent and wipe gently. Then, wipe off the remaining detergent with a dry cloth. Otherwise, it may cause discoloration. When using a chemical cloth for cleaning, read the caution provided with the chemical cloth product. Discoloration on the CCD color filter When continuously shooting a bright light source such as a spotlight, the color filter of the CCD may have deteriorated and it may cause discoloration. Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period, the discoloration may remain. Do not aim the camera at strong light sources. A light source such as a spot light causes a blooming (light bleeding) or a smear (vertical lines). Smear Bright subject Blooming Use this product for indoor use only. Do not expose this product to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep this product away from water. Avoid installing in the following locations. • Locations where it may get wet from rain or water splash • Locations where a chemical agent is used such as a swimming pool (not only outdoor) • Locations subject to steam and oil smoke such as a kitchen • Locations near flammable gas or vapor • Locations where radiation or x-ray emissions are produced • Locations subject to strong magnetic field or radio waves • Locations where corrosive gas is produced • Locations where it may be damaged by briny air such as seashores • Locations where the temperature is not within –10 °C - +50 °C {14 °F - 122 °F}. • Locations subject to vibrations (This product is not designed for on-vehicle use.) Installing place Contact your dealer for assistance if you are unsure of an appropriate place in your particular environment. Make sure that the installation area is strong enough to hold the camera, such as a concrete ceiling. Do not install the camera in a humid or dust-laden environment. Otherwise, lifetime of the internal parts may be shortened. Be sure to remove this apparatus if it is not in use. Radio interference When the camera is used near TV/radio antenna, strong electric field or magnetic field (near a motor or a transformer), images may be distorted and noise sound may be produced. Mounting screws It is necessary to procure screws or bolts to mount the camera. Prepare them according to the material and strength of the area where the camera is to be installed. The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area. 9 Major Operating Controls and Their Functions TOP TOP WV-CF284T WV-CF294T WV-CF284 WV-CF294 LOCK TOP ELC ALC BLC OFF ON D/N B.S. LOCK TOP ELC ALC BLC OFF ON D/N B.S. LOCK TOP ELC ALC BLC OFF ON D/N B.S. AF LOCK TOP ELC ALC BLC OFF ON D/N B.S. AF w !0 o i u y y e r t q !1 w e r q !1 w !0 o !7 !6 i u !0 o !7 !6 i u e !2 !2 !3 !3 r !1 w !0 o i u e r t !4 !5 !4 !5 !1 q Video output connector (WV-CF284/CF294 only) Composite video signals are transmitted. If this unit is connected to the multiplex unit, the multiplexed VD2 that is prioritized over INT is automatically selected. w Marker This marker is used when the dome cover is installed. e Monitor output jack (RCA jack) Connects the LCD monitor and such devices for checking images. r Dip switch Selects ON/OFF of light control mode, backlight compensation, Adaptive Black Stretch or Simple day/night mode. B.S. BLC ALC D/N ON ELC OFF • Simple day/night mode selector [D/N] ON: The camera selects black-andwhite mode if the picture is dark, or color mode if the picture is bright enough. OFF: Color picture is displayed normal ly. Default setting: OFF Note: The simple day/night function is established by utilizing the SENSE UP function for B/W images. The IR filter is secured. • Adaptive Black Stretch selector [B.S.] ON: The dark area of the object is auto matically corrected to lighten it. OFF: Does not compensate. Default setting: ON Important: In the case of "ON" setting, noise may be increased in the dark area of the object. In addition, darkness and brightness may be emphasized in the vicinity o...