Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
increase increase BRIGHT CONTRAST V.HOLD 5. Height (4) This recessed screwdriver control should be adjusted simultaneously to give proper vertical height consistent with good vertical linearity. Adjustment should be made to extend the picture limits approximately 1/10" beyond the top and bottom edges of the mask at over scanning operation. 6. Vertical Linearity (6) This recessed screwdriver control should be adjusted to give proper vertical linearity. 7. Focus (8) The clearest picture is produced when this screwdriver control is adjusted. 8. DC Restoration (10) DC restoration circuit provides a stable reference for the black level. Set the switch to ON position to prevent excessive contrast and preserve shadow detail. INSTALLATION CAUTION: The following installation should be made by qualified service personnel or system installers. Mounting into EIA Standard 19” Rack Model WV-BM503 can be mounted into EIA 19" rack as shown below. WV-BM503 (Part No. YWL831-EM01A) CONNECTIONS Power Cable 1. Keep the camera Power switched OFF during installation. 2. Connect the Power Cord (16) to a 60 Hz grounded electrical outle; 120V AC . Video Cable 1. Use the RG-59/U (3C-2V), RG-6/U (5C-2V). RG-11/U (7C-2V) or RG-15/U (10C-2V) coaxial cable. 2. Up to 10 monitors can be hooked up in this configuration before signal loss occurs. Total cable length should not exceed 500 feet (150m). 3. Wiring Precautions • Do not bend coaxial cable into a curve whose radius is smaller than 10 times of its diamefer. • Never crush or pinch the cable All these will change the impedance of the cable and cause poor picture quality Recommended maximum cable length Cable RG-59/U (3C-2V) RG-6U (5C-2V) RG-11/U (7C-2V) RG-15/U (10C-2V) Recommended maximum cable length .№) 1650 2475 3300 4125 (m) 500 750 1000 1250 External Sync ' When a non-composite video signal is connected to the monitor, it will be necessary to connect an external composite sync signal to the monitor. 1. Connect the Sync Input Connector (14) on the video monitor to the sync signal source by means of a 75S1 coaxial cable. 2. Set the Sync Selector Switch (13) at EXT position. NOTE: 1. Non-composite video signal is a signal without sync. 2. External sync should be composed of mixed H. Sync and V. sync signals, not H. and V. drive pulse signals. Composite Sync Level: 4.0 Vp-p (2.0 Vp-p - 5.0 Vp-p) SYSTEM CONNECTION 1. Single Monitor Connection m_QMSOO 2. Multiple Monitor Connection WV-BM500 -9- Internal Sync Connection • Connect the Video Input Connector (11) on the monitor to the Video Out Terminal of cameras with 75-ohm coaxial cables. External Sync Connection • When a non-composite video signal is connected to the video monitor, it must also have an external composite SYNC signal connected to the video monitor. • Set the Sync Selector Switch (13) at EXT position. • Loop through connection of sync signal is the same as the case of Video Signal. SPECIFICATIONS Power Source : Power Consumption : Tube Size : Video Input Impedance : Video Input Leve : Resolution : Scanning Frequency : Sweep Linearity :" External Sync Input impedance : External Sync Input Level : Operating Ambient Temperature Operating Ambient Humidity : Dimensions : Weight : 120V AC60Hz WV-BM500 Approx. 14W, WV-BM503 Approx. 42W 5" diagonal actual visual size (5.5” diagonal tube screen size) 75£2 or high impedance (Auto Termination) 1.0 Vp-p composite (0.5 Vp-p - 2.0 Vp-p) More than 700 lines (Horizontal at center) Horizontal : 15.75kHz Vertical : 60Hz Horizontal ; Less than 5% Vertical : Less than 5% 750 or high impedance (Auto Termination) 4.0 Vp-p negative (2.0 Vp-p - 5,0 Vp-p) 14°F - 122°F(-10°C-+50°C) Less than 90 % WV-BM500: Approx. 5-13/16" (W) x 7-1/16' (H) x 9-5/8” (D) [147 (W) x 180 (H)x 245(D) mm] WV-BM503: Approx. 19" (W) x 7”(H) x 10-1/16” (D) [480 (W) x 177 (H) x 256 (D) mm] WV-BM500: Approx. 5.1 lbs [2.3 kg] WV-BM503: Approx. 19.8 lbs [9 kg] Weight and dimension indicated above are approximate. Specitications are subject to change without notice. -10- STANDARD ACCESSORIES (Supplied) WV-BM503 • Fixing Screws for Rack Panel ......................2 pcs. (Part No. ; YWL831-EM01A) • Fiber Washers..............................................2 pcs. (Part No. : YWL1201ER01) Panasonic Broadcast & Television Systems Company Division of Matsushita Electric Corporation of America_ CLOSED CIRCUIT VIDEO EQUIPMENT DIVISION Executive Office: One Panasonic Way, Secaucus, New Jersey 07094 Regional Offices: Northeast: 43 Hartz Way, Secaucus, NJ 07094 (201) 348-7303 Southeast: 1854 Shackleford Court, Suite 115, Norcross, CA 30003 (404) 717-6835 Midwest: 1707 North Randall Road, Elgin, IL 60123 (708) 460-5200 Southwest: 4500 Amon Carter Blvd., Ft. Worth, TX 76155 (817) 685-1117 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7365 MATSUSHITA ELECTRIC OF CANADA LIMITED 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada...