Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Single Monitor Connection WV-BM1400 Connect the Video Input Connector(H) on this monitor to the Video Output Connector of the video source with a coaxial cable. 2. Multiple Monitor Connection TV Camera Q= Coax. Cable I I I I p ( u ? v J ID ^-*4 7T[7M Ô First Video Monitor n □ N Last Video Monitor Connect the Video Input Connector (11) on this monitor to the Video Output Connector of the video source with a coaxial cable. Connect the Video Output Connector (12) on this monitor to the Video Input Connector (11) on the second monitor with a coaxial cable. Complete the connections of all monitors in the system according to the above procedure. 3. External Sync Connection ' When a non-composite video signal is supplied to the monitor, an external composite sync signal must also be supplied to the monitor. TV Camera Non-Composite Connect the Video Input Connector (11) on the monitor to the Video Output Connector of the video source with a coaxial cable. Connect the Video Output Connector (12) oh the first monitor to the Video Input Connector (11) on the second monitor with a coaxial cable. Complete the connections of all monitors in the system according to the above procedure. Set the Internal/External Selection Switch (15) to the EXT position. Supply the sync signal source to the Sync Input Connector (16) on the first monitor with a coaxial cable. Connect the Sync Output Connector (17) on the first monitor to the Sync Input Connector (16) on the second monitor with a coaxial cable. Complete the connections of all monitors according to the above procedure. ADJUSTMENT OPERATION Under Scanning Under Scanning is obtained by setting the Scan Size Selection Switch (3) to the UNDER position. m. UNDER JL NORMAL SCAN SIZE DC Restoration The DC restoration circuit provides a stable reference for the black level. Set the DC Restoration Switch to the ON position to preserve black or shadow detail when the black level of the object is bright and the picture is losing black level. 2. If the picture slips to either side, or appears as a series of horizontal strips, adjust the Horizontal Hold Control (4) until a stable picture is obtained. H.HOLD 3. If the picture rolls up or down, adjust the Vertical Hold Control (6). V.HOLD 4. The recessed screwdriver controls, HEIGHT and V. LINEARITY, should be adjusted simultaneously to give proper vertical height consistent with good vertical linearity. Adjustments should be made to extend the picture limits approximately 1/4" beyond the top and bottom edges of the CRT mask. Preparations: Make sure that all required connections in the system are completed. Turn on the power of this monitor by pressing the Power On/Off Switch(1) on the front panel. OFF □ O POWER 1. Adjust the Bright Control (8) and Contrast Control (10) so that the overall brightness is appropriate and gray tones are resolved. BRIGHT CONTRAST INSTALLATION Mounting into EIA Standard 19” Rack Note: Rack mounting requires the purchase of optional WV-Q21W Rack Mount Adaptor. © Remove the four Cover Fixing Screws. (D Remove the four Rubber Feet. (3) Align the Rack Mount Adaptor to the four holes on the monitor, and attach with screws provided with the Adaptors. © Mount into EIA Standard 19” Rack. (D Attach the monitor to the rack with rack mount screws (not provided). Caution : If a fan is used to keep the temperature in the rack below 122°F (50°C), it should be installed away from the monitor to avoid picture disturbance. SPECIFICATIONS Power Source: Power Consumption : Video Input: External Sync Input: Horizontal Resolution : H.AEC Time Constant: Sweep Linearity: Sweep Geometry: Overscanning : Scanning Size: DC Restoration : Tube Size : High Voltage : Ambient Operating Temperature Ambient Operating Humidity: Dimensions : Weight: 100-240V AC, 50/60 Hz Approx. 37 watts 1.0 Vp-p composite/75 ohms 4.0 Vp-p composite/75 ohms 1000 lines at center Short/Long time constant switchable Less than 5% at overscan Less than 2% at overscan Approx. 5% Overscan or underscan switchable Yes 12*11/16" diagonal actual visual size (14” diagonal tube screen size) DC 13kV 14°F - 122°F {-10°C - 50°C) Less than 90% 12-5/8"(W) X 12-11/16"(H) X 14-1/8"(D) 320{W) X 322(H) X 358.5(D) mm 19.8 lbs (9 kg) Weight and dimensions shown are approximate. Specifications are subject to change without notice. STANDARD ACCESSORY Power Cord........................................... ..............1 pc. OPTIONAL ACCESSORY Rack Mount Adaptor............................................WV-Q21W -7- Panasonic Broadcast & Television Systems Company Division of Matsushita Electric Corporation of America_ CLOSED CIRCUIT VIDEO EQUIPMENT DIVISION Executive Office: One Panasonic Way, Secaucus, New Jersey 07094 Regional Offices: Northeast: 43 Hartz Way, Secaucus, NJ 07094 (201) 348-7303 Southeast: 1S54 Shackleford Court, Suite 115, Norcross, CA 30003 (404) 717-6835 Midwest...