Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Panasonic
Dateigröße: 2.26 mb
Dateiname: WJNT104.PDF
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
Contact qualified service personnel for maintenance. • Handle the appliance with care. Do not strike or shake, as this may damage the appliance. • Do not expose the appliance to water or moisture, nor try to operate it in wet areas. Do take immediate action if the appliance becomes wet. Turn the power off and refer servicing to qualified service personnel. Moisture may damage the appliance and also cause electric shock. • Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently. • Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do not use the appliance in an extreme environment where high temperature or high humidity exists. Use the appliance at temperatures within -10°C -+503C (14°F - 122°F) and a humidity below 90 %. The input power source for this appliance is 120 V AC 60 Hz. MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS Front View © @© Panasonic OPE (ATE d b U IK О RÍ .V XI IT О О Network Interface Unit WJ-NT104 TZZT ■ RearView © Operate indicator [OPERATE] Is on while the power of the WJ-NT104 is turned on. (D Link indicator [LINK] Lights when the unit is connected to a normally operating network. (D Receiving indicator [RCV] Lights when data is received from the network. © Transmitting indicator [XMT] Lights when data is transmitted to the network. © Front panel © Reset button [RESET] Used to set or change a mode, or to restart. ф RS-232C port [RS232] Used as an alternative to the RS-232C port © on the rear panel. 6 © Mode selector [MODE] Used to sel a mode. Set all the switches to OFF except when setting a mode. • SW1 To initialize the IP address (IP=192.168.0.10) or other data already sel. • It takes about 10 seconds after SW1 is set to ON and the RESET button is pressed for the data to be initialized. • After initializing, set SW1 back to OFF and press the RESET button aqain to restart. * SW2 To return the HTML file, JPEG or other image data stored in the WJ-NT104 to the factory default settings. The IP address and other setup data will not be initialized. • It lakes a few minutes after SW2 is set to ON and the RESET button is pressed for the data to be initialized. • After initializing, set SW2 back to OFF and press the RESET button again to restart. To return all data, including settings and home page, to the factory default settings, set both SW1 and SW2 to ON and press the RESET button. • SW3, SW4, SW5, SW6, SW7, SW8, SW10 Keep these in the OFF position. • SW9 Selects the RS-232C port (front or rear panel). Setting SW9 to OFF selects the rear panel port, setting it to ON selects the front panel port. MODE IflflBBBBBBflfl S1 23456789 10 Switch Positions SWT SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 To operate OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF To initialize ON ON OFF OFF OFF OFF OFF OFF OFF OFF © Video input connectors [VIDEO IN 1/2/3/4] (BNC) Used to connect cameras. © RS-485 connectors [XMT/RCV] To connect the control data cables of combination cameras (options) (fj) RS-485 setup switches [RS485 SETUP] Used when combination cameras with an RS-485 interface are connected. © Ethernet port [10BASE-T} To connect a lOBase-T cable. © DC power connector [DC 12V IN] To connect the AC adapter (accessory). © Cord clamp (accessory) To clamp the cord of the AC adapter (accessory). Insert the clamp into the hole in the rear panel shown below. RS-485 mode SW1 SW2 SW3 SW4 Half Duplex (2 Lines)/termination ON ON ON ON ON Full Duplex {4 Lines)/termination ON ON OFF OFF ON Half Duplex (2 Lines)/termination OFF OFF ON ON ON Full Duplex (4 Lines)/termination OFF OFF OFF ON ON SET UP ÏDQBQ SI 2 3 4 © Alarm input/output port [ALARM] To connect an external alarm unit. Input and output can be changed from the ADMINISTRATOR SETUP PAGE. © Video output connectors [VIDEO OUT 1/2/3/4] (BNC) The video signal connected to VIDEO IN is looped through to this connector. © RS-232C port [RS-232C] To connect a modem or CCTV equipment for controlling the system. 7 INSTALLATIONS The installation described below should be made by qualified service personal or system installers. ■ Mounting in a Rack The WJ-NT104 can be mounted in a rack using the optional WV-Q204/1 mounting brackets. Use of the optional WV-204/2 mounting brackets permits mounting up to two WJ-NT104 units in a rack side by side. 1. Remove the four rubber feet by removing the four screws from the bottom of the WJ-NT104. • Mounting one WJ-NT104 with the WV-Q204/1 2. Fix the mounting brackets (large and small) on both sides of the WJ-NT104 with the eight supplied screws (M3x8) as shown below. bracket (large) • Mounting two WJ-NT104 with the WV-Q204/2 2. Place the joint metals on the WJ-NT104 units as shown below and fix them with the twelve supplied screws (M3x6) Note: Remove two ...