Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Move the Joystick to activate the Pan/Tilt unit and adjust the camera Angle. Press the Focus (FAR/NEAR) Key or the Zoom (TELE/WIDE) Key to adjust lens focus or lens zoom. To release controlling the camera, press the Menu (MENU) Key to display the Main Menu, then select [DSTN] on the menu by pressing the Joystick. Press the Menu (MENU) Key to return to normal viewing. -14- (2) Camera Preset Position Caution: The following function is only available if the pre* set position registration of a destination camera has been attempted from the local site. 1. Press the Menu (MENU) Key to display the Main Menu on the monitor screen. 2. ,Move the high-lighted bar to [DSTN] by moving the Joystick then press the Joystick to execute the selection. “CONTROLLING” display appears on the upper right corner of the monitor screen. Main Menu lajm HD I controlling! CONTROLLING Main Menu © 3. Press the Menu (MENU) Key to return to normal viewing. In this state, the camera in the destination site can be effected. 4. Press the Numeric Keys 1-8 correspond to the preset position numbers, to activate the Pan/Tilt Unit to move to the preset position. 5. To release controlling the camera, press the Menu (MENU) Key to display the Main Menu, then select [DSTN] on the menu by pressing the Joystick. 6. Press the Menu (MENU) Key to return to normal viewing. Note: Refer to the Setting of Camera’s Preset Positions on page 24 for setup methode. 8. Destination Picture Selection Caution: The following function is only available with the Panasonic Vision Series 300 or the Vision Series 500 is used in both site. It is used to select a picture from the destination site. 1. Press the Menu (MENU) Key to display the Main Menu on the monitor screen. 2. Move the high-lighted bar to [DSTN] by moving the Joystick then press the Joystick to execute the selection. “CONTROLLING” display appears on the upper right corner of the monitor screen. Move the high-lighted bar to [SELECT] by moving the Joystick then press the Joystick to select Camera Selection Menu on the monitor screen. I controlling" Camera Selection 4. Move the high-lighted bar to the desired mode by moving the Joystick then press the Joystick to execute the selection. MAIN: Selects destination site Main Camera picture SUB: Selects destination site Sub Camera picture LINE: Selects destination site picture connected to the Line Input such as VCR. 5. To release selecting the picture from the destination site, move the high-lighted bar to [MAIN MENU] by moving the Joystick, then press the Joystick to return to the Main Menu. Select [DSTN] by pressing the Joystick to escape from the destination site. 6. Press the Menu (MENU) Key to return to normal viewing. Caution: If the Vision Series 300 is controlled form the destination site, “CONTROLLED” display appears on the upper right corner of the monitor screen. In this case, the destination control cannot be released from the local site. Note: While “CONTROLLING” is displayed on the monitor screen, it is possible to select picture in the destination site without displaying the menu screen. Press the Numeric ( # ) Key repeatedly, the picture is selected the following sequence. 9. Data Transmission • Data exchange with the destination site is possible using personal computer, for example, is connected to the Data Port (DATA PORT (RS-232C)) of the AV Codec. • During the conference, data exchange is effective regardless of the system operation. Caution: • Data exchange cannot be effected unless the data port setting is correct. • Refer to the Data Port Setup on page 33 for Setup method. 10. MLC (Multi Location Conference) • When 3 BRI lines are used at the Local Site (calling point), simultaneous transmission of video and audio signals is available from the Local Site (calling point) to up to other three locations (receiving points). From the Local Site, two way communication is available between the Local Site and the one of the location selected (receiving point). • Operation during a conference and closing a conference are the same as those for an normal video-conference. Note: Some steps are required the registration of the MLC Numbers and the MLC Sites. Refer to the MLC Registration No. on page 22 for registration method. (1) Connection with MLC Site 1. Press the Dial (DIAL) Key to display the following Dial Input Menu on the monitor screen. №»1 Dial the number and press CALL Key 2. Press the Multi Location Conference (MLC) Key to display the MLC Selection Menu on the monitor screen. 4. SI I Select MLC No. and press CALL key I No. MLC TITLE I 1/2 CD Test-MLC 1 4 m rri m m I SITE I : [#Key] Cancel : [DIAL KEY] While in this menu, move the Joystick to the right to select the next page or move the Joystick to the left to back up to the previous page. 3. Select the desired MLC No. by pressing the Numeric Key, or move the high-lighted bar to the desired MLC No. by moving the Joystick the...