Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Image resolution setting [RESOLUTION] A resolution of camera images is selectable from the following: NORMAL: Horizontal resolution of 480 TV lines or more HIGH (default): Horizontal resolution of 540 TV lines typ. Note: When the electronic sensitivity enhancement function, "SENS UP", is activated under the condition that "HIGH" is selected, noise may increase. 11. Settings in black-and-white mode [BW MODE] The settings regarding the black-and-white mode are performed. Follow the procedure below for settings regarding the black-and-white mode. "CAMERA SETUP" screen "BW MODE" screen "BW MODE" screen **CAMERA SETUP** 1/2 CAMERA ID OFF ALC/ELC ALC SHUTTER OFF AGC ON SENS UP OFF SYNC INT WHITE BAL ATW1 MOTION DET OFF DNR HIGH RESOLUTION HIGH BW MODE **BW MODE** BW OFF BURST(BW) ON RET TOP END **BW MODE** BW AUTO1 LEVEL HIGH DURATION TIME .|.. S L BURST(BW) ON RET TOP END AUTO1: Automatically toggles between color Step 1 and black-and-white images in accordance with the screen brightness (illumi- Move the cursor to "BW MODE" and press nance). The black-and-white mode is the setting button. selected for dark images, and the color > The "BW MODE" screen appears. mode is selected for bright images. AUTO2: Uses a near-infrared light source at Step 2 nighttime. EXT: Is selected to control switching Move the cursor to "BW" and select the between color and black-and-white black-and-white control from the following: images after connecting an external device to the external terminal (DAY/ NIGHT). ( page 18) ON: Displays black-and-white images. OFF (default): Displays color images. Note: If a subject is always moving or the screen is occupied with a uniform color, brightness determination may be not performed successfully because the brightness is merely determined by information from the CCD image sensor. When "AUTO2" is selected, the wave length of the light source shall be 800 nm or longer. Step 3 Move the cursor to "LEVEL" and select a brightness level at which switching between color and black-and-white images is performed from the following: LOW: Switches from color to black-and-white images when the ambient brightness (illuminance) of the camera is approx. 0.1 lx or less. (when the AGC MAX level is set to the top end.) HIGH (default): Switches from color to blackand- white images when the ambient brightness (illuminance) of the camera is approx. 0.2 lx or less. (when the AGC MAX level is set to the top end.) Step 4 Move the cursor to "DURATION TIME" and select a time for switching between color and black-and-white images from the following: (Default: 30 seconds) 10 sec.- 30 sec.- 60 sec.- 300 sec. (S) (L) Step 5 Move the cursor to "BURST (BW)", and decide whether or not to provide a burst signal output in the black-and-white mode with use of "ON" or "OFF". ON (default): Provides a burst signal output. OFF: Does not provide any burst signal out put. Notes: • The auto back focus function also allows users to correct out of focus when changing between color and black-andwhite images. ( page 45) • Images may not be displayed appropriately without burst signals when camera images are displayed in the black-andwhite mode depending on a monitor or VCR model to be used. In such a case, set the burst signal output to "ON". 12. Privacy zone setting [PRIVACY ZONE] When undesired portions in the camera shooting area (on the screen) exist, those portions (privacy zone) are hidden. ON (1): Grays the zone. ON (2): Mosaics the zone. OFF (default): Displays the zone normally. Up to 8 portions can be specified for the privacy zone. Follow the procedure below for privacy zone setting. Note: The privacy zone function is disabled at initializing the unit, i.e. right after turning on the power. "CAMERA SETUP" screen Zone number selection screen Zone setting screen **CAMERA SETUP** 2/2 PRIVACY ZONE OFF MIRROR OFF LENS-DRIVE DC STABILIZER OFF RET TOP END **ZONE NUMBER 1 /8** RET TOP END **ZONE NUMBER 1 /8** POSITION PUSH SW SCALE PUSH SW SET DEL RET TOP END Step 1 Move the cursor to "PRIVACY ZONE", select "ON (1)" or "ON (2)", and press the setting button. > The zone number selection screen appears. Step 2 Use the right or left button to select the target zone number after ascertaining that the cursor is present on "1" of "1/8" located at the right side of "ZONE NUMBER". When a zone number is marked with "*" at its right side, the zone with the number is already set to the privacy zone. Step 3 Press the setting button after zone number selection. > The zone setting screen appears. Notes: • When a zone number that is already set to the privacy zone in Step 3 is selected, the image of the zone is displayed in the zone frame on the zone setting screen. Performing Step 4 and Step 5 clears the setting zone and implements new zone setting. • To cancel the zone setting, move the cursor to "DEL" and press the setting button. The zone setting is canceled. Step 4 Move the cursor to "POSITION" and press the setting button. Step 5 Use the up, down, ...