Anleitung Panasonic, modell VLGC003A
Hersteller: Panasonic
Dateigröße: 613.6 kb
Dateiname: VLGC003A.PDF
Unterrichtssprache:
|
 
|
|
|
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Left/right range Center of the door station Center of the door station Side view of the camera facing the front at 0 . at 0 . right at 15 . 66 66 Top view of the camera facing the front Image range: 960 mm (3713/16") 480 mm 480 mm (1829/32") (1829/32") 500 mm 87 (1911/16") Top view of the camera facing the left or Image range: 1080 mm (4217/32") 270 mm (105/8") 810 mm (317/8") 500 mm (1911/16") 87 8 Installation Introductions Note: L The measurements and angles are for reference purposes and may vary depending on the environment. L If a strong light is shining on the door station, the visitor’s face may not be distinguishable. Do not place the door station in the following locations: – Where most of the background is the sky. – Where the background is a white wall reflecting direct sunlight. – Where direct sunlight will shine on the door station. – Where echoing occurs, causing the unit to beep frequently. L Make sure the back of the door station is not subject to water exposure. Important: L When the camera angle is set facing the upper left or upper right, the image may be slightly curved. Wire type and distance L Wire (between the monitor station and the door station): Type: General cable CAT-3 24 AWG Distance: Maximum 100 m (about 328 feet) Switch box L Switch box (to install the door station easily): Type: Gang box with conduit knockout Size: 3" x 2" (Depth: 1 1/2" over) – 3 switch boxes are needed for installation. Installation Introductions Installing the door station Important: L An optional face panel must be purchased beforehand (page 5). L On the bottom surface of the door station, there is a hole to allow water to drain. Do not cover it up when installing. 1 Connect the wire to the terminal connector. L See page 9 for the wire type and distance. L You can change the camera angle using the camera angle control lever. See page 7 for details. Terminal connector Camera angle control lever Door station Screw Wire (Not included) Installation Introductions 2 Attach and fix the door station. L Before drilling, see page 7 for installation location. Door station 92mm (319/32") 83.5mm (319/64") Opening to insert the back of door station (73mm x 141mm, 27/8" x 51/2") Wood screw Note: L Using the switch box (page 9) is easier to install. Door station Switch box Inch screw Installation Introductions 3 Install the optional face panel as shown. L Be sure to install the optional face panel (VL-GF001A) to avoid malfunction. 1. Loosen the screw attached to the bottom of the door station. 2. Set the hooks (1) on the face panel into the slots (2) and cover. 3. Press and hold (3), while fasten by tightening the screw to fasten. Slots Door station Hooks Screw (Attached to the door station) Face panel Help Cleaning Use a soft, dry cloth when cleaning. For excessive dirt, wipe the unit with a slightly damp cloth. Important: L Do not use anything containing alcohol, polish powder, powder soap, benzine, thinner, wax, petroleum, or boiling water. Also do not spray with insecticide, glass cleaner, or hair spray. This could cause a change in color or quality. General Information Technical data about this product Power supply*1: Standby: Approximately 5 V DC (2 mA) At operation: Approximately 20 V DC (180 mA) Dimensions: Approximate height 165 mm x width 115 mm x depth 51 mm (61/2" x 41/2" x 2") Mass (Weight): Approximately 225 g (0.5 lb.) Operating environment: –10 °C to 50 °C (14 °F – 122 °F), Up to 90% RH (Relative Humidity) non condensing Installation method: Flush mount External material: ABS (V-0) Image pickup device: 1/4" CCD (0.25 megapixel) Minimum subject illumination: 1 lux within 500 mm (19 3/4") from the door station *1 Supplied from the monitor station. Note: L Design and specifications are subject to change without notice. L The pictures and illustrations in these instructions may vary slightly from the actual product. General Information FCC and Other Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or tele...
)