Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
• To change the settings of a zone, select the zone number and repeat from step 3. B Image stabilizer setting [STABILIZER] whether or not to enable the image stabilizer is determined. This function is effective for the case that the camera is installed at a place with slight shaking. ON: Enables the image stabilizer. OFF (default): disables the image stabilizer. Important: • When "ON" is selected for the image stabilizer, the view angle becomes narrower and the resolution becomes lower. when "ON" is selected for the image stabilizer, check the view angle and resolution at camera installation. • The image stabilizer function may not work for the following subjects. • Dark subject • Less contrasty subject (e.g. white wall) • Subject shaking at excessive speed • Large amplitude image shaking C Electronic zoom setting [EL-ZOOM] whether or not to use the electronic zoom is determined. ON: Uses the electronic zoom. OFF (default): does not use the electronic zoom. When "ON" is selected, the zoom factor and the panning/tilting settings can be configured. Follow the procedure below. “SYSTEM SETUP” screen EL-zoom setting screen Zoom setting screenPan/tilt setting screen **EL-ZOOM** PUSH SET PUSH SET **EL-ZOOM** PUSH SETPUSH SET **EL-ZOOM** PUSH SETPUSH SET ZOOM PAN/TILT ZOOM PAN/TILT ZOOM PAN/TILT U ZOOM D U ZOOM D L PAN R RET TOP END RET TOP END RET TOP END OFF **SYSTEM SETUP** SYNC INT PRIVACY ZONE STABILIZER OFF EL-ZOOM ON UPSIDE-DOWN OFF -+ LDC I...... 0 RET TOP END Step 1 Move the cursor to "EL-ZOOM", select "ON" and press the [SET] button. > The "EL-ZOOM" setting screen will be displayed. Step 2 Move the cursor to "PUSH SET" of "ZOOM" and press the [SET] button. > The zoom setting screen appears. Step 3 Adjust the angular field of view by changing the electronic zoom factor (up to 2x) using the [UP] or [DOWN] button, and press the [SET] button. Note: • When the zoom factor is incremented, resolution will be deteriorated. Step 4 Move the cursor to "PUSH SET" of "PAN/TILT" and press the [SET] button. > The pan/tilt setting screen appears. Step 5 Use the [UP], [DOWN], [RIGHT], and [LEFT] buttons to determine the position of the area to be set and press the [SET] button. The position can be changed in the range of zoom factor set in the "ZOOM" setting screen. D Upside-down setting [UPSIDE-DOWN] ON: The video image can be reversed upside down. OFF (default): The video image cannot be reversed upside down. E Lens distortion correction [LDC] The image may be distorted depending on the lens used and the zoom factor. By adjusting the lens distortion correction setting, the distorted image can be converted to match the square monitor and achieve effects desired by the user. Note: • Depending on the lens used, complete correction may not be achieved. Special menu setting [SPECIAL SETUP] Special menu setting [SPECIAL SETUP] The special menu setup is performed including the setting of the camera image quality and the communication configuration when a decoder is used. The following settings are to be configured on the "SPECIAL SETUP" screen displayed from the top screen. Refer to page 5-6 for how to call up the screen. "SPECIAL SETUP" screen **SPECIAL SETUP** CHROMA GAIN ....I..160 AP GAIN ...I... 32 ...I... 0 PEDESTAL HUE .I..... 15 -+ PIX OFF CAMERA RESET PUSH SET SER.NO. XXXXXXXX COMMUNICATION COAX RET TOP END F Chroma level adjustment [CHROMA GAIN] Use the [RIghT] or [LEfT] button to adjust the color density of the camera image. When the level indicator moves in the "+" direction, the color becomes thicker, and when the level indicator moves in the "–" direction, the color becomes thinner. Be sure to view a vector chromaticity indicator or a monitor when the adjustment is performed. G Aperture level adjustment [AP GAIN] Use the [RIghT] or [LEfT] button to adjust the image quality. When the level indicator moves in the "+" direction, the image becomes sharper, and when the level indicator moves in the "–" direction, the image becomes softer. Be sure to view a monitor when the adjustment is performed. Note: • Moire (interference fringes) may be observed when shooting a subject with fine pattern such as a carpet or a curtain. In such a case, move the indicator in the "-" direction to reduce moire. H Pedestal level adjustment [PEDESTAL] Use the [RIghT] or [LEfT] button to adjust the pedestal level of the camera. When the level indicator moves in the "+" direction, the image becomes brighter, and when the level indicator moves in the "–" direction, the image becomes darker. Be sure to view a waveform monitor or a monitor when the adjustment is performed. I Chroma phase (hue) adjustment [HUE] Use the [RIghT] or [LEfT] button to adjust the pedestal level of the camera. Be sure to view a vector chromaticity indicator or a monitor when the adjustment is performed. J Flaw compensation [PIX OFF] Flaws of pixel in the displayed camera image are corrected. Up to 16 points can be corrected. Follow the procedure below. Step 1 Move the...