Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Datavideo Dateigröße: 869.1 kb Dateiname: Unterrichtssprache:

Press on the “MENU” key to end the setup, 12 Recording Video Quality There are 4 different bit-rates offered in MP-4100 (directly related to video quality) Recording Quality Bit-rate Quality Level High 3Mbps Near-DVD quality Fine 2Mbps Super VCD quality Normal 1.2Mbps VCD quality Low 800Kbps VCR-like quality Recording Frame Rate? There are 4 selectable frame rates in MP-4100 which are 30,10, 2 or1 fps for NTSC Video and 25,8.5,1.2,0.8 fps for PAL Video Frame-rate (fps) Quality Description 30fps_NTSC Completely smooth motion after 25fps_PAL recording 10fps_NTSC Near smooth motion 8.3fps_PAL 2fps_NTSC Usually configured for longer 1.2fps_PAL recording capabilities 1fps_NTSC Usually configured for longer 0.8fps_PAL recording capabilities . 13 Recording Time in a 60GB or 80GB HDD The estimated recording time on a 60GB HDD is about 46 hours with 30fps (NTSC video) and highest video recording quality (D1 resolution of 704 x 480) The estimated recording time on a 80GB HDD is about 61 hours with 30fps (NTSC video) and highest video recording quality (D1 resolution of 704 x 480) The estimated recording time on a 120GB HDD is about 92 hours with 30fps (NTSC video) and highest video recording quality (D1 resolution of 704 x 480) 14 Alarm Settings Press on the key on RMC-110 to pop up “Main Menu”. Use key to move the highlight and select “Recording Settings”. Press on the key to enter “Recording Settings” Menu Use the key to move the highlight and select “Alarm Settings”. Press on the key to enter “Alarm Settings” Menu Use the key to move around. Use the key to specify each item. Use the key to highlight the “Save” button and press the key to save and pop up the System Settings menu. Press on the “MENU” key to end the setup. 15 Change Network IP and MASK settings Press the key on the RMC-110 Remote key to pop up the Main Menu. Use the key to move the highlight and select “System Settings”. Press on the key to enter System Settings menu and select “Connection Settings”. Select “Ethernet Settings” and press on the key. 16 Use the key or key to enable or disable. Once DHCP is enabled, DVR can obtain the IP address automatically from your DHCP server. Otherwise, you need specify the following 3 items manually. Use the key or key to specify the 32-bit IP address manually, if DHCP is disabled. Use the key or key to specify the 32-bit subnet mask manually, if DHCP is disabled. Use the key or key to specify the 32-bit default gateway manually, if DHCP is disabled. Use the key or key to specify the 32-bit SAS IP address. If it's provided, MP4100 will automatically register itself at SAS Server. Otherwise, you need to register the DVR at SAS Server manually. Only applicable for Datavideo Streaming & Archiving Server. Note: Do not set DHCP on until you are sure your MP-4100 is connected to DHCP network. If DHCP is turned on, MP-4100 will submit IP assignment request to DHCP server for getting an IP address automatically. If no DHCP server is available, MP-4100 will retry 50 times getting the IP address, which will dramatically slow down the power up process. Use the key to highlight the “Save” button, press the key. The Connection Settings menu appears. Press the “MENU” key on the front panel to end the setup, changes will be saved at this time. 17 Format Hard Disk? Press on the “MENU” key to pop up “Main Menu”. Use key to move the highlight and select “System Settings”. Press on the key to enter “System Settings” menu and select “Format Hard Disk”. Select Format Hard Disk, then press Enter key Press on the “left” key to proceed Format HDD and press Enter key to confirm. 18 Change DVR Serial Number Press on the key to pop up Main Menu and use the key to move the highlight. Select “System Settings” and press on the key to enter System Settings menu. Select “Display Settings” and press on key. Use the right key to select DVR serial number Use the key to move around and use the key to specify each item Use the key to highlight the “Save” button and press on the key to pop up “System Settings” menu. Press on the “MENU” key to end the setup, 19 Set DVR Date and Time MP-4100 uses time and date as video index therefore it’s very important to make sure that your system time is set correctly when you first use it. Procedure to set the system clock: Press on the key to pop up “Main Menu” and use the key to move the highlight. Select “System Settings” and press on the key to enter System Settings menu. Select “Set Clock” from the System Settings menu and press on the Enter key Use Us . Use e” button Pres em Settings menu and press on the MENU” to end the setup, 20 Set Date There are 3 fields for entering: Year Use the key to select a year between 2000-2016. Month Use the key to select a month between 1-12. Date Use the key to select a date between 1-31. Set Time There are 2 fields for entering: Hour Use the key to select an hour between 0-12. Minute Use the key to select a minute between 0-59. am/pm It is automatically changed when the hour...

Herunterladen

Geben Sie zwei Ziffern: